Dimensions Of The etrailer Scissor Stabilizer Jacks w/ Handle # TJSCHD-24-4 Mounting Brackets
Updated 05/16/2024 | Published 05/13/2024
Question:
Is there any 3D available, at least on the top plate that is being attached to the trailer? There are some dimensions like thickness or contact area that are not available.
asked by: Edgar
0
Expert Reply:
Hey Edgar,
I've attached a diagram below that should have all the measurements you need for the mounting brackets of the etrailer Scissor Stabilizer Jacks w/ Handle # TJSCHD-24-4. The brackets are about an 1/8" thick.
expert reply by:
Kevin C
0
Bolt Pattern
(click to enlarge)
(click to enlarge)
Product Page this Question was Asked From
Scissor Stabilizer Jacks w/ Handle - 18-3/4" Lift - 10,000 lbs - Qty 4
- Camper Jacks
- 5th Wheel Camper
- Pop Up Camper
- RV Motorhome
- Teardrop Camper
- Travel Trailer
- Scissor Jacks
- Steel
- 9001 - 10000 lbs
- Manual Jack
- 18-3/4 Inch Lift
- Bolt-On
- 4 Jacks
- etrailer
more information >
Continue Researching
- Shop: Scissor Stabilizer Jacks w/ Handle - 18-3/4" Lift - 10,000 lbs - Qty 4
- Search Results: bearing cap
- Video: Feature Breakdown: Scissor Stabilizer Jack
- Q&A: Will Scissor Stabilizer Jacks Fit 2021 Heartland Pioneer DS320
- Search Results: scissor stabilizer jacks
- Search Results: stabilizer jacks trailer jack
- Video: Comprehensive Review: Scissor Stabilizer Jacks w/ Handle
- Shop: Power Mountain Tallboy Off-Road Bottle Jack - 8-1/2" to 37-3/4" Lift - 6 Tons
- Shop: etrailer Scissor Stabilizer Jacks w/ Handle and Drill Adapter - 24" Lift - 5,000 lbs - Qty 2
- Search Results: rv fresh water tank accessories and parts
- Shop: Adjustable Width Trailer Hitch Receiver for RVs, 22" to 66" Wide
- Q&A: How to Determine if Scissor Jack Will Fit Camper
- Search Results: tounge jack
- Search Results: tongue jack
- Shop: Replacement Entry Door Hinge for RV - 6 Leaf - White
- Search Results: rv fireplaces
- Shop: Curt Adjustable Trailer Hitch Receiver - 18"-51" Wide - 2" Drop - Class III - 2"
- Shop: etrailer Scissor Stabilizer Jacks w/ Handle and Drill Adapter - 24" Lift - 30,000 lbs - Qty 4
- Q&A: Can etrailer Scissor Jack be Used as a Replacement for a Jayco Camper?
- Video: What to Know About the Camco Fold-Away RV Grab Handle
- Shop: Trailer Hitch
- Q&A: What is Difference Between etrailer Scissor Jacks TJSCHD-24 and e56VV
- Video: Review of etrailer Camper Jacks - Scissor Stabilizer Jacks Qty 4 - e74RV
- Video: Pacbrake Alpha HD Rear Air Bag Suspension DIY Installation - 2017 Chevrolet Silverado 2500
- Shop: RV Interior Lighting
- Video: Review of etrailer Camper Jacks - Scissor Stabilizer Jacks Qty 2 - e29VV
- Video: Trailer Valet Drill-Powered Stabilizer Jack Spec Review
- Q&A: How To Connect The Mr. Heater Buddy To RVs QD on Propane System
- Q&A: Replacement Scissor Jacks Needed for Forest River Wolf Pup
- Q&A: Aligning a Trailer Axle with the Center Bolt on a Spring
Edgar
5/15/2024
Thanks for the information, but I till don’t see one important dimension for me, the plates that are being attached to the trailer have some sort of bends on the sides, the dimesion I need is related to the flat area that will indeed have contact with the trailer, and the general dimension includes the bends.