What Size Wax Screw is Used to Attach Solera Drive Head to Roller Shaft

Question

Question:

Please help me identify the size of this waxed screw? Took it out to replace awning arm and it is stripped. Solera electric awning shaft into the roller head.

asked by: Cathy

0

Expert Reply:

The wax screw you're referring to I believe is a #8 - 32 x 1/2”.

expert reply by: Conner L

0

What Size Wax Screw is Used to Attach Solera Drive Head to Roller Shaft
(click to enlarge)

Answer 1

Hey it sounds like you are on the right track here, Blake. The Kodiak Disc Brake Caliper #KDBC225DAC is exactly what we recommend for replacing the Tie Down 46304 calipers. We have confirmed on multiple occasions that the Kodiak caliper is a suitable…

view full answer...

Answer 2

Based on the pictures you definitely need the awning support arm #LC281154. I can't tell in that other photo if the pin is bent or damaged, or just barely hanging in there. I'm also not sure if your idler head and roller endcap are ok or not…

view full answer...

Answer 3

I spoke with Lippert, and they informed me that for your Lippert awning you are going to need the: -Replacement Gear Pack for Lippert Solera Awning Motor #LC78VR, with the Replacement Head Pin for Solera Power Awning Gear Drive Head #LC93FR.

view full answer...

Answer 4

I attached a picture of what the wax screws look like for the Solera awnings like of the #LC289561 instructions that you referenced. Basically it's under the black cap that you'll pop off and you'll unscrew that you see in the second…

view full answer...

Answer 5

Hey Jim, we sell the replacement screws to use with the replacement cap part #LC423751 as the part #LC266156 but based on the price of them it might make more sense to get them locally. These are: Screw type: #6 Screw diameter: 1/8" Screw…

view full answer...

Answer 6

The correct screws for the Solera Awning Plain Drive Head #LC289561, are #6-15 UNF x 1/2”.

view full answer...

Answer 7

I'll go ahead and list out all the replacement black rear head covers for Solera power awnings, and you can scroll down to see photos of them to compare to yours. Just note that some are a replacement specifically for the drive head and some for…

view full answer...

Answer 8

I am not totally sure which Solera awning setup you have but we do have a few options you can check out and see which one matches what you need. We have the part #LC643922, #LC289560, and #LC32NJ.

view full answer...

Answer 9

In order to separate two awning head covers such as the Solera Awning Plain Drive Head Front Cover part #LC289560 and the Solera Awning Plain Drive Head Back Cover part #LC289561 you'll need to remove the screws which are accessed from the back…

view full answer...

Answer 10

The replacement plug/grommet you are looking for is the Replacement Manual Override Grommet for Solera Powered RV Awnings #LC95ED. So this will be what you need to fill the hole in your awning head (even though the replacement drive head cover really…

view full answer...

Answer 11

That's actually a drive head in your picture as you can see the motor. That means the correct cover is the part #LC289560.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

What Size Wax Screw is Used to Attach Solera Drive Head to Roller Shaft

Product Page this Question was Asked From

Continue Researching