Best Way To Attach Trailer Plug Bracket To A Trailer Hitch Without A Pre Welded Bracket
Published 07/12/2023
Products Featured in This Question
Question:
I was wrong about the hitch having a welded mounting point for a backet to hold a 4 flat to 7 blade adapter. My proposed alternative is to flip reverse the bracket, drill two small holes = 5/32 through the face of the bracket. Two threaded holes into the rear vertical section of the trailer hitch. Then mount the bracket using screws into the #13485 Curt hitch. » Would drilling two 5/32 holes into the face of the hitch weaken it? » Would it void any warranty? » Please advise an alternative solution.
asked by: James
Expert Reply:
As far as the mounting bracket, you can absolutely screw it directly to the hitch if you want. We do this frequently in our own installs and it will not compromise the strength of the hitch in any way. Now putting a few holes in the hitch does open up the potential for rust, since we are compromising the powder coating, but the risk is small. You could use the bracket # BK4F for a 4-flat or use the # C67UR for a 7 way, and a self tapping screw like # 101131802.
If you do not want to drill into the hitch, you can use a no drill bracket # 18140. This basically uses a hose clamp around the crosstube of the hitch, and give you a mounting point for the bracket # BK4F or # C67UR without having to put holes in the hitch.
Product Page this Question was Asked From
Curt T-Connector Vehicle Wiring Harness with 4-Way Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Vehicle End Connector
- Powered Converter
- No Tow Package
- 4 Flat
- Plug and Lead
- Plug-In
- Hidden
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: Brake Controller
- Shop: No-Drill Mount for Electrical Mounting Bracket - Short
- Search Results: cre
- Search Results: 4400 lbs trailer leaf springs
- Search Results: reese trailer hitch
- Search Results: self tapping screws
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Search Results: kayak trailer
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V - 2-1/2"
- Shop: Suspension Enhancement
- Shop: Hex Screw - Self Drilling Unslotted Washer Head #8 x 1/2"
- Search Results: 7 pin to 4 pin
- Search Results: add promo code
- Shop: Coghlan's Storage Capsule - Watertight - 13/16" Wide x 2-7/16" Long - Silver
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Curt Dual Connection Socket w/ Bracket - 7-Way RV Style and 4-Way Flat - Vehicle End
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Options to Replace Shelby 5764A Trailer Jack
- Article: How to Accurately Measure Trailer Leaf Springs
- Q&A: Replacement Trailer Lights for Shorelandr Boat Trailer
- Shop: Vehicle Tow Bar Wiring
- Q&A: How To Measure To Make Sure The MORryde CRE3000 Equalizers Will Fit Your Trailer
- Q&A: How To Measure For Replacement Leaf Springs When Current Springs Are Flat
- Q&A: How to Tell When Travel Trailer Leaf Springs Need to be Replaced
- Q&A: Can A 25-1/4" Leaf Spring Be Replaced With A 26" Leaf Spring?
- Q&A: Difference Between 3 and 4 Leaf Spring Stack for 3,500 Pound Axle
- Video: All About the Shocker Hitch Impact Max Cushioned Ball Mount- 2-5/16" Ball- 2" Hitch
- Shop: Towing Mirrors
on Custom Fit Vehicle Wiring
