Replacement 2 inch Hitch Adapter for Thule Hitching Post Pro Bike Rack

Question

Question:

I need a replacement 1/4 to 2 adapter for a Thule bike rack. I am not sure what model rack I have. Can I send a photo or can you advise me where to find the model number?

asked by: Dana F

0

Expert Reply:

Thanks for the picture of your rack. Based on that I can see that you have a Thule Hitching Post Pro bike rack part # TX934XTR so the correct 2 inch hitch adapter would be the part # 853-7489.

expert reply by: Jameson C

0

Thule Hitching Post Pro
(click to enlarge)

Answer 1

The correct receiver will depend on the bike rack that you have, as each have a different shape and pin hole placement. Since it's an older rack, your most likely fit is part #853-7292, for the Ridgeline 4 bike, or Roadway 2 or 4 bike. Without…

view full answer...

Answer 2

All Thule bike racks use the same hitch pin, so you will want the Replacement Threaded Pin for Thule Snug Tite Hitch Lock and Anti-Rattle Device #853-5917 or the complete pin and lock kit #THSTL2. This is the 12mm thread you mentioned.

view full answer...

Answer 3

On your Thule Apex XT 4 Bike #TH9025XT, the pin should go into your trailer hitch receiver hole and into the rack shank on the one side only. It won't go all the way through to the other side but will solidify the rack in place and then you will…

view full answer...

Answer 4

The Thule DoubleTrack has a specific 2 inch hitch adapter that you need. For that you want the part #853-7489.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Replacement 2 inch Hitch Adapter for Thule Hitching Post Pro Bike Rack

Products Featured in This Question

Continue Researching