Replacement Thule 12mm Threaded Hitch Pin for Bike Racks

Question

Question:

I have a Thule bike rack and am missing the threaded hitch pin that is 12 mm and am not sure which one to buy. None of them tell you the thread size.

asked by: Chris

0

Expert Reply:

All Thule bike racks use the same hitch pin, so you will want the Replacement Threaded Pin for Thule Snug Tite Hitch Lock and Anti-Rattle Device # 853-5917 or the complete pin and lock kit # THSTL2. This is the 12mm thread you mentioned.

expert reply by: Jason S

0

Answer 1

Hello Ashley, thanks for reaching out. I am happy to look into this. Can you tell me exactly what brand and model of bike rack you have? Typically, the locking hitch pins are model specific to the bike rack, so if you can tell me what you have, I…

view full answer...

Answer 2

If you live in an area where it is currently cold (since this is February) then the issue is that the rubber strap like part #753-3535 are being difficult to stretch due to the cold. Try heating the rubber straps up a little by taking the bike rack…

view full answer...

Answer 3

The correct receiver will depend on the bike rack that you have, as each have a different shape and pin hole placement. Since it's an older rack, your most likely fit is part #853-7292, for the Ridgeline 4 bike, or Roadway 2 or 4 bike. Without…

view full answer...

Answer 4

On your Thule Apex XT 4 Bike #TH9025XT, the pin should go into your trailer hitch receiver hole and into the rack shank on the one side only. It won't go all the way through to the other side but will solidify the rack in place and then you will…

view full answer...

Answer 5

Thanks for the picture of your rack. Based on that I can see that you have a Thule Hitching Post Pro bike rack part #TX934XTR so the correct 2 inch hitch adapter would be the part #853-7489.

view full answer...

Answer 6

The Thule DoubleTrack has a specific 2 inch hitch adapter that you need. For that you want the part #853-7489.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Thule 12mm Threaded Hitch Pin for Bike Racks

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching