Length of Snap-Up Lever for Fastway e2 Weight Distribution Systems

Question

Question:

What is the measurement of the fastway e2 lift bar?

asked by: KM

0

Expert Reply:

I'm assuming you mean the length of the Snap-Up Lever for Fastway e2 Weight Distribution Systems # FA92-00-6000. It is 19.5" long. If you're asking about capacity it doesn't have anything specific but is capable of handling any Fastway or Equal-i-zer weight distribution system.

expert reply by: Robin H

0

Answer 1

This could be a magnet wiring problem. It is unlikely that the magnets are bad on newer assemblies, but if the wiring is not properly connected, it could cause problems. Check to see that the magnets are properly grounded to a clean, bare metal…

view full answer...

Answer 2

Hey Steve, it sounds like you are looking for a replacement snap up lever for your Equal-i-zer system which is part #EQ95-01-6050.

view full answer...

Answer 3

Yes, the replacement snap up lever part #EQ95-01-6050 does also work with Fastway e2 weight distribution systems.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 10

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Length of Snap-Up Lever for Fastway e2 Weight Distribution Systems

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching