Replacement Cradle for a Thule Passage Trunk Mount Bike Rack

Question

Question:

For the Thule Passage TH910XT, does the T3 cradle 853-5829 serve as a replacement cradle? According to specs/size measurements it should, I just want to verify with the experts.

asked by: Gregg

0

Expert Reply:

The correct replacement cradle for the Thule Passage bike rack # TH910XT is actually the Stay-Put cradle # 853-7887. If you also need a strap it is # 852-3006-001 and the anti-sway cage that fits is # 853-7758.

expert reply by: Michael H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 9

Hey Ron, congrats on the new SUV. To add a hitch and a wiring harness to your 2026 Toyota RAV4 Hybrid, I recommend the Curt Hitch item #C34FR62ZY and the Curt Powered Tail Light Converter item #C59236. The Curt Hitch item #C34FR62ZY is custom fit for…

view full answer...

Answer 10

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 11

Hello Matt, Thanks for writing in! I'm glad you found us. We did originally have the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #118784 listed as a fit for the 2025 Hyundai Santa Cruz. However, we had to remove it from our…

view full answer...

Answer 12

Hey Lawrence, thanks for reaching out. The Curt T-Connector #C56040 is correct for the 2025 Subaru Forester Hybrid. The factory harness plug should be in the rear cargo area behind the driver side access panel. If you remove the trunk floor covering…

view full answer...

Replacement Cradle for a Thule Passage Trunk Mount Bike Rack

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching