Replacement for a 14,000 lbs Underslung A-Frame Trailer Coupler

Question

Question:

is there a repair kit for the a frame trailer coupler for 2 5/16. The pin holding the mechanism is worn and keeps falling out. Can if buy a new pin or one slightly larger

asked by: Duane

0

Expert Reply:

With this being such an inexpensive part there is not a repair kit offered by the manufacturer for the thumb latch components of the A-Frame Trailer Coupler item # CA-5335-B. I wish I had an option for you but if your pin is no longer functional you will need to replace the entire coupler.

expert reply by: Jerred H

0

Answer 1

I do see that several of models for the 2023 Jayco White Hawk travel trailer use an Underslung Coupler #CA-5335-B. If this is what you have you will want to use the AMPLock Trailer Coupler Lock #AMP56FR. This is one of the best locks available as it…

view full answer...

Answer 2

There is not a repair kit for the thumb latch of the A-Frame Trailer Coupler - Underslung - Thumb Latch - Black - 2-5/16" Ball #CA-5335-B. While I wish we had an option for you, if yours has busted you will need to replace the entire coupler.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Replacement for a 14,000 lbs Underslung A-Frame Trailer Coupler

Product Page this Question was Asked From

Continue Researching