Can A-Frame Coupler Fit Old Airstream Trailer

Question

Question:

I have a vintage 1968, 31, sovereign landyatch airstream trailer. The coupler is mounted or welded to the underneath frame. The latching/ball locking mechanism was damaged beyond repair The coupler, however, is in good condition. Will this underslung coupler fit this old airstream since bit appears there are no repair kit for this makes. TY for your time and recommendations.

asked by: James K

0

Expert Reply:

So long as your Airstream trailer has an A-frame, then yes, you can use the A-Frame Trailer Coupler - Underslung # CA-5335-B.

There is no way for us to know what couplers fit any specific trailer, but so long as you have an A-frame then there won't be an issue with this one.

expert reply by: Kyle S

0

Mark Y.

6/4/2026

I know you make an adjustable height coupler adapter for trailers. Because I have one that lowers my coupler to 13" off the ground with my ALUMA 8216 car hauler. Is there also a way to have a. adjustable height coupler adapter for a smaller Airstream travel trailer?

Claire H.

6/4/2026

@MarkY You can have an adjustable trailer coupler welded onto your Airstream's trailer tongue so that you can raise or lower the trailer to work with your tow vehicle's height. To get the right adjustable channel coupler for you, you'll need to select one that can handle the weight of your trailer and fits your ball mount (whether it's a 2 5/16" ball or 2" ball). There are 5 position and 3 position adjustable trailer couplers so you can choose which one you think would work best for how much drop/rise you need. I've linked a 5 position and 3 position adjustable channel trailer coupler as an example for you.

Mark Y.

6/4/2026

@ClaireH Reread my question. I already own am E TRAILER bolt on adjustable coupler part #DM 3867-52 that I am using Aluma 8216 car hauler. I would send you a picture if I could post in this reply. Do you have a bolt on adjustable coupler for different models of Airstream trailers?

Claire H.

6/5/2026

@MarkY We don't have any information as to what will specifically fit an Airstream trailer since their frames/tongues vary between models. Most Airstream travel trailers have an A-frame tongue, if that's the case for what you have, you can use the Lock N Roll 50 degree A-frame Coupler w/Jack Hole part # LR76VR. It can be bolted on by using the existing vertical holes (17/32" diameter) to install bolts through the trailer tongue where possible. You can also drill additional horizontal holes for support as needed.

Answer 1

The etrailer A-Frame Trailer Coupler w/ Round Jack Hole #CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest point is approximately 9" long. I have include…

view full answer...

Answer 2

I don't think you are doing anything wrong apart from jumping on the truck and even that isn't wrong it's just more fun to jump on a trampoline or in puddles. There are several reasons why the coupler could be having a hard time releasing…

view full answer...

Answer 3

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 4

There will be some play with any ball and coupler because the trailer has to rotate. However, it sounds like you have too much movement because putting another hitch ball in place seemed to fit better. I recommend changing the hitch ball in your…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Can A-Frame Coupler Fit Old Airstream Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching