Height From Bracket to Top of 1,100 lb Xtreme Off-Road Swing-Up Jack w/ Dual Wheels

Question

Question:

In the position where the wheels are in the upper most position, what is the length of the jack above the upper most bolting holes - shown in the attached picture, in red?

asked by: Troy

0

Expert Reply:

The measurement you're asking for on the Xtreme Off-Road Swing-Up Jack w/ Dual Wheels # ORJW500D is 62mm which is about 2.44" when converted to the US system.

Attached is a photo showing this spec as well as a review video for you to check out.

expert reply by: Jon G

0

What Height is This for the 1,100 lb Ark Xtreme Off-Road Jack
(click to enlarge)

Bracket Height Dimensions for 1,100 lb Ark Xtreme Off-Road Jack
(click to enlarge)

Answer 1

Good afternoon Stephany, I'm sorry you had that less-than-stellar experience with the pin style anti-rattle device. Normally that setup works pretty well, but in some extreme towing situations, I definitely think the clamp style is better at…

view full answer...

Answer 2

Hey Lance, thanks for reaching out! The etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers #e38FV is currently (March 2025) a little behind on demand, so while this part is technically live and "available", it sold out really…

view full answer...

Answer 3

I got my hands on the Removable Xtreme Off-Road Swing-Up Trailer Jack #ARK47FR and was able to determine that it can accept a 2" outer diameter tube inside the mounting tube and has a 5/8" diameter retention pin. If you remove the current…

view full answer...

Answer 4

Hello Bret, The Ark Xtreme Off-Road Swivel Trailer Jack w/ 2 Wheels #ARK47FR rotates tire to rear when stowed.

view full answer...

Answer 5

Hey Eric, thanks for the picture! The etrailer Anti-Rattle Hitch Collar item #e38FV is not going to fit but I have one that will. It is the Blue Ox Hitch Receiver Immobilizer II item #BX88224. You're receiver doesn't have the necessary gap…

view full answer...

Answer 6

Hey John, the etrailer anti-rattle device part #e38FV is powdercoated steel so it's not going to rust. Are you in an area that gets a lot of salt on the roads in the winter?

view full answer...

Answer 7

Yes, Luke, you should be able to use the etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers - Pre-Order #E38FV in combination with a hitch extender such as Curt Hitch Extender for 2" Hitch Receivers - 8" Long #C76DR. I say…

view full answer...

Answer 8

Hey Jim! The etrailer Anti-Rattle Hitch Collar #e38FV is still a pre-order right now so if your trip is in the near future it probably won't be available. Once it comes out, you could use our dealer locator I linked below to find a dealer in Palm…

view full answer...

Answer 9

Hello Forrest, thanks for reaching out. The mounting plate for the Ark Xtreme Off-Road Tube Mount Swivel Trailer Jack #ARK47FR is 7-1/2" x 5-1/2" overall. I have included a picture with more detailed dimensions for you. What kind of trailer…

view full answer...

Answer 10

The diameter of the pull pin that holds the #ARK47FR jack in place on the mounting bracket is .5512".

view full answer...

Answer 11

Hey Jason. The etrailer Anti-Rattle Hitch Collar item #e38FV will stop any rattling or vibrations you're feeling that are transferred from your ball mount through your hitch. However, seeing as how you have a boat trailer I'm guessing what…

view full answer...

Answer 12

Hey John, the threads of the etrailer Anti-Rattle Hitch Collar #e38FV that you referenced do not have loc tite on them but you wouldn't have to worry about the bolt coming loose since it'll be pretty tight.

view full answer...

Height From Bracket to Top of 1,100 lb Xtreme Off-Road Swing-Up Jack w/ Dual Wheels

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching