Availability of Replacement Lock for Torklift FastGun Turnbuckles

Question

Question:

Is TLA 7509 compatible with Torklift Fastguns? I ‘ped’ a Torklift lock, and only need 1 for my Fastguns, and don’t need to buy a set of 4. I realize that I will be adding another key to my ever growing RV keys, if it is compatible. Thanks, Tony

asked by: T C

0

Answer 1

Hey John, thanks for reaching out. The Pin Locks for TorkLift FastGun and Derringer Turnbuckle Handles #TLS9500 will work with your existing QuickDraw tie-downs. I know you were looking to replace the one pinlock but these only come in a set of 4.…

view full answer...

Answer 2

The etrailer Trailer Coupler Latch Lock part #e98889 is very similar to the Pin Lock for TorkLift GlowStep Scissor Steps part #TLA7509 so you should be able to swap the two without issue. The etrailer lock is threaded unlike the TorkLift so there…

view full answer...

Answer 3

Unfortunately no, the Pin Locks for TorkLift FastGun and Derringer Turnbuckle Handles #TLS9500 will all use the same key, however the TorkLift Tie Down Locks #TLS9700 will use a different set of keys as they are not able to be keyed alike.

view full answer...

Answer 4

The turn buckle locks we offer are the Pin Locks for TorkLift FastGun and Derringer Turnbuckle Item #TLS9500 and TorkLift Tie Down Locks Item #TLS9700. Keep in mind TLS9700 is not compatible with the Talon R Series Tie Downs.

view full answer...

Answer 5

For a single replacement Pin Lock you will need part #TL11001. It is a direct replacement for your pin lock with the key P01. My contact at TorkLift verified that all of them are keyed alike so you will not have to give any specific part numbers when…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Availability of Replacement Lock for Torklift FastGun Turnbuckles

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching