Can the TorkLift Tie Down Locks and the Pin Locks Be Keyed Alike?

Question

Question:

Hi Can I buy 4 each of S9700 and S9500 torq lift with matching lock keys?

asked by: Patrick K

0

Expert Reply:

Unfortunately no, the Pin Locks for TorkLift FastGun and Derringer Turnbuckle Handles # TLS9500 will all use the same key, however the TorkLift Tie Down Locks # TLS9700 will use a different set of keys as they are not able to be keyed alike.

expert reply by: Bryce D

0

Answer 1

The turn buckle locks we offer are the Pin Locks for TorkLift FastGun and Derringer Turnbuckle Item #TLS9500 and TorkLift Tie Down Locks Item #TLS9700. Keep in mind TLS9700 is not compatible with the Talon R Series Tie Downs.

view full answer...

Answer 2

Though we do not have a replacement grommets for the TorkLift pin lock you can purchase The Replacement Pin Lock for TorkLift FastGun and Derringer Turnbuckle Handles #TL11001 which replaces the whole pin lock. The lock will secure the TorkLift…

view full answer...

Answer 3

We have the Torklift 60 inch hitch extender part #TLE1560 which is 60 inches long.

view full answer...

Answer 4

The etrailer Trailer Coupler Latch Lock part #e98889 is very similar to the Pin Lock for TorkLift GlowStep Scissor Steps part #TLA7509 so you should be able to swap the two without issue. The etrailer lock is threaded unlike the TorkLift so there…

view full answer...

Answer 5

For a single replacement pin lock for the Torklift Fastguns we have the part #TL11001 which would be what you would need. The #TLA7509 doesn't have a wide enough usable span to work with the FastGuns #TLS9522-2-LK.

view full answer...

Answer 6

The outside diameter of the receiver portion for the Hitch Extender for Brophy Hitch-Mounted Stairs #RHSE is about 2-1/2" while the shank portion (that fits in your vehicle's hitch receiver) is about 2". Please note that this was…

view full answer...

Answer 7

Hey Paul! The short range FastGun Turnbuckles are designed for bed-mounted tie-downs and I would definitely listen to what Kingstar recommends. These are only available in pairs and you will need a pair for the front and rear. You can choose from the…

view full answer...

Answer 8

Hey Joyce, congrats on the potential new purchase. Which tie-downs you need are going to depend on what length bed you get and what type of hitch your 2025 GMC Sierra 2500 has. I have listed the options below: 6-3/4' Bed with a Factory Hitch or…

view full answer...

Answer 9

For a single replacement Pin Lock you will need part #TL11001. It is a direct replacement for your pin lock with the key P01. My contact at TorkLift verified that all of them are keyed alike so you will not have to give any specific part numbers when…

view full answer...

Answer 10

Hello Alan, thanks for reaching out. I see you already placed an order for the TorkLift Tie Downs #TL86NR. I just wanted to touch base and confirm the Tie Downs you ordered are correct for the 2025 GMC 2500 Denali with the 6-3/4' bed. They will…

view full answer...

Answer 11

Hey Kent, thanks for the information. If your 2024 Ford F-350 is a 4WD model, I recommend the SumoSprings Rebel Custom Helper Springs item #SSR-128-40-2. These have a 3,000 lbs leveling capacity and replace your factory bump stops. The springs have a…

view full answer...

Answer 12

Hey Bob, thanks for the information and congrats on the new truck. The correct tie downs for your 2025 GMC Sierra 2500 are the TorkLift Tie Downs - Custom Frame Mount - Front and Rear item #TL86NR. This is a set of custom fit front and rear tie downs…

view full answer...

Can the TorkLift Tie Down Locks and the Pin Locks Be Keyed Alike?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching