Pin Locks for TorkLift FastGun and Derringer Turnbuckle Handles

Question

Question:

I have Torklift Quickdraw TieDowns and lost the locking part for one of the pinlocks. So I just need one. My question is if the lock part of this product will work with my existing Quickdraw TieDown pin photo attached. Thank you.

asked by: John D

0

Pin Lock
(click to enlarge)

Expert Reply:

Hey John, thanks for reaching out.

The Pin Locks for TorkLift FastGun and Derringer Turnbuckle Handles # TLS9500 will work with your existing QuickDraw tie-downs. I know you were looking to replace the one pinlock but these only come in a set of 4. You'd be able to replace the missing lock but also have extras for just in case something like this happens in the future.

Are you using FastGun turnbuckles with your QuickDraw tie-downs or a different style of turnbuckle?

expert reply by: James D

0

John D.

5/12/2026

Thanks for your reply. I must've mistakenly posted this for the wrong product. It looks like you sell a single pinlock for Pin Lock for TorkLift GlowStep Scissor Steps - Part Number: TLA7509 https://www.etrailer.com/Accessories-and-Parts/TorkLift/TLA7509.html Will the lock for this part work with my existing pin for my FastGun pinlock?

James D.

5/13/2026

@JohnD I seen that but I can not confirm that the shank diameter or length on the pin lock for TLA7509 would work for the FastGuns. I advise going with the safe/confirmed option.

Ross C.

5/13/2026

@JohnD I lost one of my pin locks on my fast guns. The only one I could fond as a single was the Glow Step one. The problem was the pin was Not long enough for the Fast Guns. I then went and bought the 4 pack

Johnd

5/13/2026

@RossC - Thanks for your input. I have the opposite situation. I have the pin, need the lock. In your experience, is the pin diameter the same between the two? If so, I would assume the single Glow Step would give me the lock part that would work with my Fast Gun pin.

See All (4) Replies to John D. ∨

Steve

5/13/2026

Only 3 of the 4 locks worked but the ones that work do fine. We do not use turnbuckles.

Answer 1

For a single replacement pin lock for the Torklift Fastguns we have the part #TL11001 which would be what you would need. The #TLA7509 doesn't have a wide enough usable span to work with the FastGuns #TLS9522-2-LK.

view full answer...

Answer 2

Hey Conner, thanks for reaching out! I'm attaching a link to our returns policy for your reference. You aren't the only one in this situation where tire chains like the Titan Chain Snow Tire Chains #TC1530 are required for travel but may not…

view full answer...

Answer 3

In regards to the TorkLift GlowStep Stow N' Go Scissor Steps part #TLA7833, there is indeed a 6-1/2" gap between the first/last step and the mounting plate. This is needed in order for the steps to fully retract. It is not the intention of…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Pin Locks for TorkLift FastGun and Derringer Turnbuckle Handles

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching