Best Brake Controller for a 2020 Jeep Cherokee Trailhawk

Question

Question:

Hi- I have a 2020 Jeep Cherokee Trailhawk. Bought it used. Previous owners had the Mopar hitch installed as well as the 4 pin and 7 pin connectors. Which brake controller do you recommend for easy installation? Will be towing nuCamp T@B 320s Boondock which has a 2900 GVWR. Thank you.

asked by: Chris

0

Expert Reply:

I have the perfect brake controller for your 2020 Jeep Cherokee Trailhawk. It is the Redarc Tow-Pro Liberty Brake Controller item # RED24FR. This is a proportional brake controller that will engage your trailer's brakes when your Jeep decelerates. It activates immediately and is not time delayed. The Tow-Pro Liberty has a unique installation method that allows you to mount the main control unit out of sight behind your dash. The only part visible is the control knob.

We have a couple of other mounting options for the control knob that can go inside inserts in your dash. This will give you a clean factory look install. The Universal Mounting Panel for Redarc Tow-Pro Trailer Brake Controller Control Knob item # 331-TPSI-001 which measures 1-1/4 by 1 inch. There is also the option of using the Mounting Panel for Redarc Tow-Pro Trailer Brake Controller Control Knob item # 331-TPSI-002 for the more standard knock-out measuring 1-1/4 by 7/8 inch. I have attached a couple of pictures below that show the dimensions of these mounts.

It sounds like your 2020 Jeep Cherokee Trailhawk did not come with the factory towing package so there isn't going to be a plug and play installation available. You are going to need the Universal Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item # RED69FR to complete your installation.

expert reply by: Jerred H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

The factory brake controller connector on your 2021 Jeep Grand Cherokee is located under the dash behind the hood latch, as shown in the provided photo. Keep in mind, the connector will only be there if the vehicle has the factory tow package which…

view full answer...

Answer 10

Hello Sadie, Thanks for writing in. For your 2021 Jeep Cherokee, I'd recommend going with a Class III hitch with a 2" receiver since you're planning to carry two e-bikes and may eventually tow a small boat trailer or lightweight camper.…

view full answer...

Answer 11

Hey Brandon, I would strongly recommend sticking with the Tekonsha RF brake controller part #TK94FR. We know this works really well and it sounds like it worked well for you too. The Curt Echo is not reliable enough for me to really ever recommend it…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Best Brake Controller for a 2020 Jeep Cherokee Trailhawk

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching