Fan-Tastic Fan Series 5200 Replacement Fan Motor Assembly

Question

Question:

I have a 2015 Outdoors Rv fifth wheel with 3 model 5200 fan-tasting fans and would like to know if the replacement fan kit # FVK8017-00 will work for me? It looks like it should! Thanks

asked by: ERIC S

1

Helpful Expert Reply:

Yes, the Replacement Fan Motor Assembly Kit for Fan-Tastic-Vent Roof Fans # FVK8017-00 will work with your model 5200 Fan-Tastic-Vent.

expert reply by: Bryce D

1

Answer 1

The Create-A-Breeze roof vent is a Fan-Tastic Vent Roof Vent Fans and from your description you have a model 8000 vent. The correct replacement is the Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans #FVK8017-00. I have added a…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 4

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 12

Hi Ray! The MORryde GooseTech 5th Wheel to Gooseneck Pin Box for 11.5K to 14K Trailers #MR74MV can definitely be used in a short bed 3/4 ton pickup, like your 2024 Ram 2500. Just be aware that not all trailers have a tapered nose and you may not get…

view full answer...

Fan-Tastic Fan Series 5200 Replacement Fan Motor Assembly

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching