Is a Reverse Electric Lockout Needed on a Boat Trailer with Titan Model 60 Actuator
Updated 08/15/2013 | Published 08/14/2013
Products Featured in This Question
Question:
hello, i have a 1995 zemans boat trailer with a dico/titan model 60 actuator, and i have rebuilt/ restored the entire trailer with your help from all the parts to get it back to NEW condition. heres my question. The trailer never had reverse lock-out and i cant remember having a problem backing the trailer up, unless on a steep grade. i do remember having that problem 1 or 2 times. However, after all these years of trailer use i cant recall a time when i would have needed the lock out . Im sure it would be useful and needed in certain situations, but all boat ramps are graded on a downward slope, so im not sure if i should buy and install the cut out unit you offer or not. I am wondering why Zemans would not have installed it when they built the trailer in the fist place? Also, the brakes have always worked fine on the open road with no problems, it seems to me that this would only be a problem when confronted with a confined space and a grade which could not be avoided to get turned around. Am i missing something? It seems to be made to be an issue to address now while im doing the brake system now, but if ive never had a BIG problem in the past, i cant see where i might have one in the future. Please pass on your experience and clarification, thank you.
asked by: Scott
Expert Reply:
The issue is that with the way a surge coupler works when backing up, normally up hill, the trailer is pushing the other way which will cause the actuator to compress in sending fluid back to engage the brakes. This makes it very difficult or impossible sometimes to back the trailer up.
There are 2 kinds of lock outs to prevent this, a manual which is built into an actuator and prevents the coupler from pushing in, and there is the electric type. It will energize when the vehicle is placed in reverse and essentially close the gate and not let fluid go back to the brakes.
If it is something you never think you are going to need then you do not have to have it. But if you think it might come in handy some time at all I would say its worth the expense and effort to install it. It will thread in at the back of the master cylinder and the brake line will attach to the back of the solenoid. One wire is grounded to the trailer frame. The other goes to the reverse light pin on the trailer connector. The vehicle side connector must have a working reverse light circuit in the connector for it to work.
Then you could add # T4835800183 to protect the solenoid from damage.
Something else to consider is the weight of the boat and trailer. If the coupler is rated for 6,000 pounds but the boat and trailer is much less than that it would have a hard time pushing in the coupler to actuate the trailer brakes.
Product Page this Question was Asked From
Replacement Solenoid Valve for Dexter Brake Actuators with Reverse Lockouts
- Accessories and Parts
- Brake Actuator
- Disc Brakes
- Hydraulic Drum Brakes
- Solenoid
- Valve
- Dexter
more information >
Continue Researching
- Shop: Replacement Solenoid Valve for Dexter Brake Actuators with Reverse Lockouts
- Q&A: Adding Reverse Lockout to Trailer with Titan Model 60 Actuator
- Video: Titan Brake Actuators with Reverse Lockout Replacement Solenoid Valve Installation
- Video: Feature Breakdown: Dexter Zinc-Plated Brake Actuator
- Video: What to Know About the Demco Hydraulic Brake Actuator-DM72VR
- Shop: Dexter DX7.5 Drop-N-Go Brake Actuator - Drum Brakes - 2" Ball - Zinc Plated - 7,500 lbs
- Shop: Demco Hydraulic Brake Actuator w/ Electric Lockout - Disc - Zinc - 2" Ball - 7,000 lbs
- Shop: etrailer Hydraulic Trailer Brakes - Free Backing - E-Coat - 12" - Left/Right - 5.2K to 7K
- Shop: Dexter Galphorite Free-Backing Hydraulic Trailer Brake Assembly - 10" - Left Hand - 3,750 lbs
- Shop: Dexter Zinc-Plated Brake Actuator - Drum - Multi-Fit Ball - Bolt On - 7,000 lbs
- Shop: Demco Hydraulic Brake Actuator - Drum - Zinc - 2" Ball - 7,000 lbs
- Q&A: Surge Brake Actuator Replacement Recommendation for Atwood Model 84132
- Q&A: Will Dexter or Titan Free-Backing Drum Brakes Work with Demco Brake Actuator # DM72VR
- Q&A: Recommended Replacement for Dico Model 60 Actuator
- Q&A: How to Wire Titan # T4748800 Reverse Lock-Out Solenoid Valve
- Q&A: Installed New Brake Solenoid on Trailer and Now Fuse Keeps Blowing When Trying to Use Brakes
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer tires and wheels
- Shop: Trailer Wiring
- Video: How to Choose a Trailer Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Measure for Trailer Hitch Drop
- Shop: Suspension Enhancement
- Search Results: trailer wiring
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Search Results: trailer jack
- Shop: Brake Controller
on Accessories and Parts
