Parts Needed to Flat Tow 2021 Jeep Wrangler Unlimited

Question

Question:

Stock steel bumper

asked by: Norman O

1

Helpful Expert Reply:

What bumper do you have? A Smittbilt with a built in winch?

expert reply by: Jameson C

1

Norman O.

2/22/2022

Stock steel bumper

Jameson C.

2/22/2022

Since you have the factory steel front bumper on your 2021 Jeep Wrangler Unlimited you could use the Roadmaster Direct Connect base plate kit part # RM-521453-5 and you'd be set. This would not interfere with your winch either. In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting, and supplemental braking to flat tow your vehicle. The most popular compatible tow bar is the Falcon All Terain, # RM-522. This has non-binding arms which makes the setup very easy to connect/disconnect. For lighting/safety cables, locks, and covers for the tow bar we have the Roadmaster Falcon All Terrain kit part # RM-9243-1 which comes with all of that as one part number. The diode kit that comes with this allows you to splice into the taillight wiring so that your RV controls the vehicle taillights and does not require drilling into the taillight housings. This comes with a round 6-way connector that you will install on the front of your towed vehicle and enough coiled wire to go from there to the RV. And finally, most states now require supplemental braking in the vehicle being flat towed. The easiest system to set up and use is the Blue Ox Patriot # BLU37TR, that applies the vehicle brakes in proportion to how much the tow vehicle is braking. This is the safest way to stop and it reduces wear and tear on both vehicles. Most likely you will also need a high low adapter so that the tow bar will be level when you are flat towing. I attached a link to a page that has all of the ones we carry. I have included a couple of helpful links to our articles on flat towing for you. Be sure to consult the vehicle owners manual for more specific information on flat towing your vehicle.

Answer 1

For your 2018 Jeep Wrangler JL, I recommend starting with the Roadmaster EZ5 Base Plate Kit #RM-521453-5. This kit has removable arms to give you a very clean look when not flat towing your Jeep, and also gives you a clean connection to your tow bar…

view full answer...

Answer 2

We have all of the parts you need to flat tow your 2020 Jeep Wrangler, and while it may seem like a lot of parts, it's actually just four basic components - base plates on the Jeep, a tow bar to connect the Jeep to your motorhome, wiring to power…

view full answer...

Answer 3

Hello Tom, thanks for reaching out. Yes, you can use the Bulldog Winch Mount #BDW20353 along with a Roadmaster base plate on your 2019 Wrangler Rubicon which is part #RM-521453-5. The picture below shows an example of a similar winch mount installed…

view full answer...

Answer 4

Yes. You cannot use the Roadmaster #RM-521453-5 base plates with an aftermarket bumper. If you've already got an aftermarket bumper that has D rings you can use the #RM-035-1 (for 1" D rings) or #RM-035 (for 3/4" D-rings). Both of these…

view full answer...

Answer 5

Hey Mark, so the correct Blue Ox base plate kit to use with the Blue Ox Ascent tow bar part #BX4375. is the part #BLU53FR. For lighting you can use #C96JR, and not have to worry about cutting into the taillight housing as this plugs inline with the…

view full answer...

Answer 6

Hi Joe, Yes, you can flat tow a 2024 Jeep Wrangler 4XE - either the manual or auto transmission - and the set up as far as equipment is much the same as your '17 Wrangler. and you can easily still use your Roadmaster Nighthawk All-Terrain Tow Bar…

view full answer...

Answer 7

I sure can Galen, and thanks for the information. Since your Tiffin motorhome has the air line connection you'll need the Demco Air Force One Flat Tow Brake System for 2020 and Newer Tiffin Chassis RVs w/Factory Air Brakes item #DM55MV. This…

view full answer...

Answer 8

Hey Tracy, for a no-splice tow bar lighting solution for your 2025 Jeep Wrangler you'd want the Blue Ox part #BLU79FR. This doesn't have a 6-way on it though so you would need an adapter to go from the 4-way to it like with the part #RM59DQ…

view full answer...

Answer 9

Hello Tom, thanks for reaching out. We do have the Demco Air Force One Supplemental Braking System for Tiffin Chassis Motorhomes part #DM55MV. This kit includes the parts needed to install the Air Force One on your Jeep as your Tiffin chassis has the…

view full answer...

Answer 10

Hey Tracy, for your 2025 Jeep Wrangler we have the Curt tow bar wiring kit part #C96JR as a fit that does not require any splicing. This installs easily by plugging inline with the vehicle taillights. Since it uses a 4-way connector and you have a…

view full answer...

Answer 11

Hey Jim. The Curt Custom Tail Light Wiring Kit for Towed Vehicles item #C96JR is indeed compatible with the LED lights on your 2025 Jeep Wrangler Unlimited. It plugs into your factory wiring harness behind the tail lights. The only issue would be if…

view full answer...

Answer 12

Hey Bill, for the 2025 Ford Bronco the bumper type you go with will determine which Roadmaster base plate kit you'll need. If you go with the standard bumper you would need the part #RM79RR or if you go with the Modular bumper you would want the…

view full answer...