Need Replacement Pull Pin Kit for Dutton-Lainson Swivel Jack on Midwest Trailer Model SLXR2314LW

Question

Question:

Im looking for a replacement part for the pin assembly for a jack stand that is on a SLXR2314LW trailer. I sheared it off while moving the trailer. Do you happen to have anything like that? The jack stand does not have a part number on it that I could find....

asked by: Matthew L

0

Expert Reply:

I spoke to a technical contact at Midwest Industries and he advised that they use 800-lb-rated trailer jacks supplied by Dutton-Lainson. I contacted Dutton-Lainson and found the 800-lb jack referred to uses replacement pull pin kit # DL22449.

This kit consists of a replacement 3/8-inch diameter pull pin, spring, washer and cotter pin. Instructions are included.

Dutton-Lainson date codes their replacement parts. This kit works for jacks with a date code of 4398 and after. The date code should appear either on a safety sticker or be stamped into the jack outer tube.

expert reply by: Adam R

0

click to enlarge

Answer 1

Based on the picture you submitted the matching trailer jack we have to what you have is the Dutton Lainson part #DL22800. I attached an install video for you to check out as well. At the very worst you may have to use the bolt on brackets that come…

view full answer...

Answer 2

Dutton-Lainson jacks are manufactured right here in the US and are actually really good quality. The mount used by your current Dutton-Lainson jack wouldn't be compatible with the Fulton F2, which leaves you with a couple of options. You could…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

Hey Tim welcome back! Your ARH15AACBL2 GE AC unit has the old 410a refrigerant in it so the GE Appliances item #GE64FR you were looking at isn't going to work as a replacement. The EPA mandated R32 refrigerant has been used in all new AC's…

view full answer...

Answer 10

Hey George, best solution for you will be to go with an all new jack like the etrailer part #e95YV because Fulton is no longer in business so there isn't a way to get a replacement F2 and none of the other jacks out there use the same bolt…

view full answer...

Answer 11

Hey Brian! Yep, for your boat trailer, I’d skip the etrailer A-frame drill jack #e38AV since your trailer doesn't have that standard 3-bolt A-frame jack mount. That could be fabricated to fit, but that's a lot of unnecessary work. For a…

view full answer...

Answer 12

Good question Chris, thanks for reaching out! I searched our inventory and I was not able to find a side mount trailer jack that would fit a 5" frame. The Trailer Valet JXS Drill Powered Swivel Trailer Jack w/ Footplate #TV64FR has the largest…

view full answer...

Need Replacement Pull Pin Kit for Dutton-Lainson Swivel Jack on Midwest Trailer Model SLXR2314LW

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching