Bolts Wont Thread On etrailer Hitch for 2013 Toyota RAV4
Published 10/18/2021
Question:
I have read all of the information regarding the flex issues with the hitch and obviously that is a problem with the hitch I purchased, will try to make it work. But I also have an issue with two of the bolts sent not threading, they seem to large. I have cleaned the bolt holes and again, two fit but 2 do not. I received an email to leave a review but before doing so, I wanted to reach out and get some assistance.
asked by: Jackie M
Expert Reply:
The etrailer Trailer Hitch Receiver part # e98864 which is a fit for a 2013 Toyota RAV4 comes with M12-1.25x35mm hex bolts. These will match up with the weld nuts in the frame. If the vehicle is older, the chances of the weld nuts being dirty is high. They can usually be cleaned out with a wire brush and lube but sometimes they require tapping with a thread tap. The vehicle uses four of the same size bolts so I don't think you got the wrong size.
Unfortunately, hitches get bent during shipping and it's not impossible for them to be welded incorrectly either. These can usually be fixed by some slight bending it but we can get an exchange as well if it's too severe.
Product Page this Question was Asked From
etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 525 lbs TW
- 3500 lbs GTW
- 4000 lbs WD GTW
- 2 Inch Hitch
- 525 lbs WD TW
- Visible Cross Tube
- etrailer
more information >
Featured Help Information
Instructions
Continue Researching
- Article: My Trailer Hitch Doesn't Fit
- Shop: Trailer Hitch
- Q&A: What Vehicles Does the etrailer Trailer Hitch Receiver e98864 for a Toyota Rav4 Fit
- Q&A: Will the Rhino Rack Nautic Stack Kayak Carrier S520 fit a 2012 Toyota Rav 4
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Erickson Aluminum Mobility / Cargo Carrier - 30-1/4" Wide x 50" Long - 400 lbs
- Video: Installing the Curt Trailer Hitch Receiver on a 2025 Toyota RAV4
- Search Results: trailer hitch
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer wiring
- Article: Trailer Wiring Diagrams
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: Suspension Enhancement
- Search Results: trailer jack
- Q&A: Comparing the Curt Hitch C13416 and EcoHitch Hitch 306-X7396 for a 2019 Toyota RAV4
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Article: How to Choose the Right Trailer Hitch Class
- Video: Inside Look at TowSmart and Oris Hitches with the Manufacturer
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer hitch ball mount
- Q&A: Comparing Trailer Mate Trailer Hitch To Curt and B&W For 2019 Toyota RAV4 LE
- Shop: Brake Controller
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Base Plate for Tow Bar
on Trailer Hitch
