What Vehicles Does the etrailer Trailer Hitch Receiver e98864 for a Toyota Rav4 Fit

Question

Question:

can this receiver be fitted on any other make and model of vehicle?

asked by: Kristen D

0

Expert Reply:

The etrailer Trailer Hitch Receiver part # e98864 is listed as a fit for a 2006 - 2018 Toyota RAV4. Generally speaking, trailer hitches are not cross-compatible with other makes/models unless they use the same chassis. Most trailer hitches are custom fit products.

expert reply by: Conner L

0

Answer 1

The Rhino-Rack Nautic Stack Kayak Carrier, #RRS520, can carry 1 to 4 kayaks, but the number of kayaks that you can carry with the width of the roof rack on you 2012 Toyota RAV4 will be limited. Trying to carry more than 2 kayaks on the RAV4 factory…

view full answer...

Answer 2

The etrailer Trailer Hitch Receiver part #e98864 which is a fit for a 2013 Toyota RAV4 comes with M12-1.25x35mm hex bolts. These will match up with the weld nuts in the frame. If the vehicle is older, the chances of the weld nuts being dirty is high.…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 6

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

Answer 7

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 8

Hi Stephanie! Great question and you’re totally right to ask, because most hitches for the 2024 RAV4 do require a bit of bumper trimming. That includes the Oris Detachable Hitch #TS66VR, since it uses a hidden design that needs a hole cut in the…

view full answer...

Answer 9

Hey Tanner! These hitches are all pretty similar so it can be hard to decide between them. If I were you I would choose the Curt #C77MJ over the other two. The Curt #C77MJ and etrailer #e84ZV actually share the same design, and both have the…

view full answer...

Answer 10

You will need a different converter charger if you are going to lithium batteries, which is what I believe you are asking. The right one will depend on how many amp hours you need though, like the 100 amp-hour #34282738. I have added a link below to…

view full answer...

Answer 11

Hey Gerald, the Curt hitch part #C13406 would be your best option for your 2013 Toyota RAV4 as it is a Class III like you want, has the highest clearance since it fits right up under the rear bumper and is mostly hidden since only the hitch opening…

view full answer...

Answer 12

I compared ground clearance measurements for all of the 2" trailer hitch receivers we have for your 2017 Toyota RAV4 and found that the Curt Trailer Hitch Receiver part #C13406 has a great clearance from the ground to the top of the hitch…

view full answer...

What Vehicles Does the etrailer Trailer Hitch Receiver e98864 for a Toyota Rav4 Fit

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching