Replacement Leg for 4160 Happijac Camper Jack

Question

Question:

I need to replace the rear passenger Happijac on our Northern LIte truck camper. Our current setup is electric with remote. Would you be able to help us with this? Thank you,

asked by: Sarah M

0

Expert Reply:

Since you have the Happijac 4160 setup on your Northern Lite truck camper the correct leg replacement is the part # LC736514.

expert reply by: Jameson C

0

Answer 1

Hey Kelly, thanks for the pictures. Sorry to hear about your jacks being damaged. Unfortunately, since your Happijac 4160 system has the clutched motor head, I do not have a replacement for just the motor head. The 4160 is a 2-piece construction ACME…

view full answer...

Answer 2

Hello Josh, I completely understand where you are coming from. When you need long, equal-length turnbuckles to span about 35 inches on a 2022 F-350 with a Lance 1130, the goal is a setup that fits cleanly, installs easily, and stays secure without…

view full answer...

Answer 3

The HappiJac Electric Truck Camper Jack System #LC736514-ELKIT is the replacement kit for the 4100 series jacks that you have. It uses the same Replacement Jack #LC736514 and Motor Head #LC759927 for the front and rear jack positions.

view full answer...

Answer 4

Since your 2019 Grand Design Reflection 303RLS has 5,200 lbs Dexter axles you will most likely have 25-1/4" long double eyed leaf springs. You will want to measure to confirm but if this is what your 5th wheel currently has you will want the…

view full answer...

Answer 5

Hey John, yes the Everchill #EV27FR would fit in a 25 inch deep cabinet like you mentioned. This would be a really solid option to replace your Norcold so I think you should go for it. This is also our best fitting option for replacing what you have…

view full answer...

Answer 6

Hey Matt, that restoration is looking good! Yes, the etrailer Swivel Jack w/ Bolt-On Mounting Plate #e54RV will work with your trailer. Unless I'm way off, it looks like your frame isn't more than 3" deep which is the only real…

view full answer...

Answer 7

Good news! I was able to get a exploded diagram as well as a set of instructions on how to replace the rod and gears #TJD-12000-RODNUT in the #12000 Series Ram Jacks made after 2012. I have attached them to this page for your convenience. Basically,…

view full answer...

Answer 8

To access the gears inside of the heavy-duty Bulldog jacks, like part #BD182415 to install the #BD500250 you simply remove the screws that are holding on the plate covering the top of the jack. Once that plate is removed, the gears, pins and handle…

view full answer...

Answer 9

Hey Adam, thanks for reaching out. Unfortunately, the Reese Titan hitch extender 45018 is currently unavailable. Reese's parent company went belly-up and they stopped shipping and producing product. It sounds like the company was recently bought…

view full answer...

Answer 10

Each of the motors of the Happijac Electric Truck Camper Jack System #LC736515-ELKIT is protected with a 25 amp fuse. So it can pull right up to 25 amps.

view full answer...

Answer 11

If you're looking for just the L-bracket for your HappiJac Electric Truck Camper Jack System #LC736514-ELKIT then you'll need part #LC182492. The flat bracket can be swapped out with part #LC182494 and the swing brackets can be replaced with…

view full answer...

Answer 12

Hey Simon, thanks for reaching out! I spoke with my contact at Lippert (who owns HappiJac) and they said there aren't any rebuild kits available so you'll have to get a whole new jack as part #LC736514. You can still look and see if someone…

view full answer...

Replacement Leg for 4160 Happijac Camper Jack

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching