Is it Normal for the Red Light on the Hopkins Insight Brake Controller to Stay Lit?

Question

Question:

I installed a Hopkins Plug-In Simple Brake Control Insight into my 2010 Ford King Ranch F250. When I finished the installation, I noticed that the red light in the brake controller was lit and there no key in the ignition and it has been lit for over 5 hours. I figured it would go out am I wrong in believing that. Will it drain my batteries.

asked by: Milton D

1

Helpful Expert Reply:

Since you have the Hopkins Insight Brake Controller, I confirmed with Hopkins that the red light staying on is completely normal. I also confirmed with Hopkins that the red light will not drain your 2010 Ford F-250's battery to the point where you will need to replace it.

expert reply by: Bob C

1

Answer 1

You are correct, you should only be getting output when the brake is applied, or the override switch is activated. It sounds like the controller might be bad, but to make sure, you should probably bench test it before tossing it. Use a circuit…

view full answer...

Answer 2

The red light on the manual override of the Hopkins Agility will stay on all the time. But the amperage draw is so low that it would not drain your battery. A guy that works here has one installed on his truck and has had zero problems. He's had…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 6

Hi Ben! Yes, the Redarc Tow-Pro Liberty Brake Controller #RED52VR will allow you to activate the brakes on the pop-up trailer. However, it sounds like the wiring isn't complete on the 7-way so you will also need the Wiring Kit for 2, 4, 6, and 8…

view full answer...

Answer 7

Hey Eric, thanks for reaching out. Yes, we do have a hitch and wiring that will fit your 2026 Nissan Rogue dark armor edition. Here is what I recommend: - etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2" #e93ZR…

view full answer...

Answer 8

Hey David, we can help with a brake controller install in your 2006 Jeep Wrangler that has a factory 7-way but your Jeep does not have brake controller pre-wiring so you would need to hardwire in the controller with a kit like the part #5506 and a…

view full answer...

Answer 9

Hey Rob, thanks for reaching out. We have just the thing. The wiring kit you will need is the following: - Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires #ETBC7 This kit contains everything you need…

view full answer...

Answer 10

As long as your 2019 Mercedes-Benz Sprinter 2500 has a factory plugin connection point for the adapter part #3063-P you will not need to make any modifications to the adapter, it will plug right in into the factory plug and the other end to a…

view full answer...

Answer 11

Hey Robert! If your trailer has 10" brake drums with a 5 on 4-1/2 bolt pattern, there's a good chance you have 3,500 lb axles. I can't say for sure based on the trailer year and model alone, so you will need to confirm this. If they are…

view full answer...

Answer 12

You will need a Wiring Kit #5506 to install a Brake Controller #90195 on your 1994 Chevrolet Silverado pickup. There is not a factory plug in connector on your Silverado. The wiring kit will provide you with wiring and circuit breakers to safely…

view full answer...

Is it Normal for the Red Light on the Hopkins Insight Brake Controller to Stay Lit?

Product Page this Question was Asked From

Continue Researching