Availability of Coupler for 2-5/16 inch Hitch Ball that Has Adjustable Latch

Question

Question:

Is there any manufacturer that makes an adjustable 2 5/16 coupler... Why ask... It seems a lot of us have sticking balls in the couplers. Maybe its because of the lack of adjustment...

asked by: Rhw

0

Expert Reply:

The Demco eZ latch style of couplers like the # DM16680-52 do have adjustability of the tongue mechanism that holds to the hitch ball.

expert reply by: Jameson C

0

Answer 1

To install the Demco A-Frame Trailer Coupler #DM16680-52 that you referenced, you will want to use 3/8 inch, grade 5 bolts , approximately 1-1/2 inches long (depending on how you are installing the coupler). You will want to use 5 of these bolts per…

view full answer...

Answer 2

I know this is not what you want to hear but the vast majority of trailer couplers cannot be repaired, they will instead need to be replaced. There are very few trailer coupler repair kits available and they are by no means universal. Therefore,…

view full answer...

Answer 3

You'd just have to physically go out to your trailer and measure the angle. So to do this, you'd need to get a protractor or something similar and place it on the edge of the inside on one side of the trailer frame, and check to see if the…

view full answer...

Answer 4

The bolts required to install the Demco 50-Degree A Frame Trailer Coupler #DM13205-95 are 3/8" diameter x 1-3/4" long Grade 5 bolts. I spoke with the manufacturer and they confirmed that you won't want to use Grade 8 bolts on this…

view full answer...

Answer 5

Hey Sam, thanks for reaching out. We do have 2-5/16" A-frame couplers, but I am not seeing we have one with a yoke-style latch. If you want something similar, the A-Frame Trailer Coupler #CA-5280-RB fits a 2-5/16" ball and has a…

view full answer...

Answer 6

Hey Bill! I went to inTech's website and we do not have an exact replacement for their coupler but we have something that will work. It's the Demco 50-Degree A-Frame Trailer Coupler w/ Jack Hole and Anchors item #DM16680-52. The Demco item…

view full answer...

Answer 7

The best option for your trailer is a new trailer coupler as either the latch mechanism is worn or faulty. I strongly recommend against any sort of jerry-rigging here as there is too much at stake for you and the safety of those around you. This…

view full answer...

Answer 8

It sounds like you're looking for a replacement a-frame coupler like #CA-5280-RB but in a silver-painted or zinc-plated finish. Please click on the link provided to see all bolt-on standard a-frame couplers for 2-5/16-inch balls. For the…

view full answer...

Answer 9

The Demco coupler part #DM16680-52 that you referenced can be either bolted on or welded on. You would not need to do both to securely install it.

view full answer...

Answer 10

Correct, there will need to be a small amount of wiggle room or play between the trailer coupler and hitch ball which is to allow the trailer to track and turn smoothly. If the connection point between the trailer coupler and hitch ball was too tight…

view full answer...

Answer 11

Yes, the Demco coupler part #DM16680-52 is safe to use on a 31 foot air stream trailer like you have. Bolting on and welding on coupler is both perfectly safe to do. I would agree bolt on is easier in a sense but if you have a welder that route would…

view full answer...

Answer 12

You could drill into the Bulldog #BD028463 and make it a bolt-on but that's not really ideal. We don't have the exact match in a bolt-on model. We do have part #BD44150WH301 for a bolt-on Bulldog coupler. It has a higher rating but the price…

view full answer...

Availability of Coupler for 2-5/16 inch Hitch Ball that Has Adjustable Latch

Product Page this Question was Asked From

Continue Researching