Size and Type Bolts Required to Install Demco A-Frame Trailer Coupler with Hole for Trailer Jack
Updated 05/17/2016 | Published 05/13/2016
Question:
what size and type of bolts do these take and how many
asked by: Willie
1
Helpful Expert Reply:
To install the Demco A-Frame Trailer Coupler # DM16680-52 that you referenced, you will want to use 3/8 inch, grade 5 bolts , approximately 1-1/2 inches long (depending on how you are installing the coupler).
You will want to use 5 of these bolts per side for a total of 10 bolts.
expert reply by:
Victoria B
1
Product Page this Question was Asked From
Demco 50-Degree A-Frame Trailer Coupler w/ Jack Hole and Anchors, eZ-Latch - 2-5/16" Ball - 21K
- A-Frame Trailer Coupler
- Standard Coupler
- 50-Degree Frame
- Bolt-On
- 21000 lbs GTW
- 2-5/16 Inch Ball Coupler
- Auto Latch
- 2-1/4 Inch Hole
- Standard Grade
- Demco
more information >
Continue Researching
- Search Results: d ring
- Search Results: tools
- Shop: Kenda Karrier KR53 ST225/75R15 Radial Trailer Tire with 15" Black Mod Wheel - 6 on 5-1/2
- Search Results: demco
- Search Results: demco a frame
- Search Results: tie down
- Search Results: chain anchor
- Search Results: spring mount
- Shop: Kenda Karrier KR53 ST225/75R15 Radial Trailer Tire with 15" Black Mod Wheel - 6 on 5-1/2
- Video: Review of Demco A-Frame Trailer Coupler - EZ Latch Coupler - DM16680-52
- Shop: Demco 50-Degree A-Frame Trailer Coupler w/ Jack Hole and Anchors, eZ-Latch - 2-5/16" Ball - 21K
- Shop: Weigh Safe Flap Jack Folding RV Stabilizing Blocks - 8" Tall - 6K - Qty 2
- Shop: Front/Center/Rear Hanger for Double-Eye Springs - 2-3/8" Tall - 9/16" Bolt Hole
- Q&A: Recommended Safety Chains and Bolt Size Needed To Attach To Demco Coupler # DM16680-52
- Q&A: U-Bolt Torque Recommendation for 1/2 inch Diameter On Trailer Suspension
- Shop: Power Mountain Tallboy Off-Road Bottle Jack - 8-1/2" to 37-3/4" Lift - 6 Tons
- Video: All About the Demco Trailer Coupler
- Video: etrailer Jack Replacement Plunger Pin Assembly Installation
- Shop: CargoSmart Forged Steel D-Ring Tie-Down Anchor - Weld On - 1/2" x 3-3/8" - 4,000 lbs
- Q&A: What Grade Bolts Are Recommended To Install Demco Channel Tongue Trailer Coupler
- Q&A: What Size Bolts Should Be Used To Install Demco A-Frame Trailer Coupler?
- Video: Feature Breakdown: Bulldog Round, A-Frame Jack
- Article: Trailer Wiring Diagrams
- Shop: RV Jack Pads
- Video: Detailed Breakdown of the Curt QuickPin No Latch A-Frame Trailer Coupler w/ Jack Hole
- Video: Ultimate Overview of the Bulldog Heavy-Duty Cast Head Coupler w/ Wedge Latch
- Video: Complete Breakdown of the Bulldog Heavy-Duty Cast Head Coupler w/ Wedge Latch
- Q&A: What is the Difference Between Bulldog and Pro Series Pipe-Mount Swivel Jacks
- Article: How to Install a Roof Rack
- Q&A: Replacement A-Frame Coupler w/ eZ-Latch