Drill Attachment to Use with Trailer Valet Trailer Dolly STC-V211

Question

Question:

Does this come with the drill attachment?

asked by: Rick T

0

Expert Reply:

The Trailer Valet Trailer Dolly part # STC-V211 is included with the drill attachment.

expert reply by: Jameson C

0

Jerry L.

11/15/2021

I have an Impact drill, what size impact socket do I need for the 5X swivel jack?

Les D.

11/19/2021

To use a drill you will need the Trailer Valet # TVDA "socket." This is not a typical lug. It is made somewhat square and not symmetrical so that you have to use their socket. Do not use with impact drill.

Answer 1

Hi Nicholas! Out of all the options we carry, I think the Trailer Valet 5X Swivel Jack and Trailer Mover - Topwind - 15" Lift - 5,000 lbs #STC-V211 you found is the best option for you. It bolts onto frames that are up to 2-3/4" wide x…

view full answer...

Answer 2

Hey Jacob, a 4,500 lb trailer is probably going to be too heavy for a person to pull around with the Trailer Valet Dolly part #TV73FR that you referenced. The dolly would be fine but even on perfectly flat pavement a single person would struggle and…

view full answer...

Answer 3

Technically if your trailer has a tongue weight (TW) of 500 lbs then it falls into the 500 lb max TW rating of the Trailer Valet 5X Swivel Jack and Trailer Mover #STC-V211. The only problem that I see is that you are at the max capacity of this jack…

view full answer...

Answer 4

No, but I have one that will! Since your caravan weighs 5,000 lbs the Ark Xtreme item #ORJW1SU is going to be way under capacity. Instead you'll want to use the Trailer Valet 5X Swivel Jack and Trailer Mover item #STC-V211. This jack attaches in…

view full answer...

Answer 5

The only solution we currently offer to manually move your trailer with a Max Coupler would be to use the Trailer Valet 5X Swivel Jack and Trailer Mover #STC-V211 that you were already looking at. This would clamp to the tongue of the trailer and…

view full answer...

Answer 6

The Trailer Valet 5X Swivel Jack and Trailer Mover #STC-V211 can work in terms of jacking your trailer up and moving it; however, it is highly unlikely it will be able to be mounted in the horizontal position as there probably won't be enough…

view full answer...

Answer 7

There is no weight rating for the Mounting Bracket, part #TV-0002. It is designed to replace the bracket for the Trailer Valet Trailer Jack, part #STC-V211. The Trailer valet has a weight capacity of 500 lbs. You may be able to install a different…

view full answer...

Answer 8

The swivel assembly of the Trailer Valet part #STC-V211 would allow it to swivel either forward or back if needed. If you have a weight distribution system most likely you would have to install this jack behind the system or you would have to only…

view full answer...

Answer 9

In regards to the Trailer Valet 5X Swivel Jack and Trailer Mover part #STC-V211, the distance from the bottom of the wheel or ground to the center of the mounting point is 11" while fully retracted.

view full answer...

Answer 10

The further forward on a trailer the less weight there is. If at all possible, move the Trailer Valet, #STC-V211, as far forward as you can on either side. The OCD in me wants to say put it on the opposite side as the regular jack. A boat trailer…

view full answer...

Answer 11

I wasn't sure exactly what dimension you were looking for on the mounting bracket of the Trailer Valet part #STC-V211 so I attached a picture that has nearly every dimension for you to check out.

view full answer...

Answer 12

We offer several types of trailer dollies in addition to the Rack-Em unit you referenced, part #RA20. This Rack-Em dolly has a 1-7/8-inch hitch ball, 13-inch tires and a tongue weight capacity of 500-lbs. For the greatest ease and safety when moving…

view full answer...

Drill Attachment to Use with Trailer Valet Trailer Dolly STC-V211

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching