Dimensions Of Replacement Mounting Bracket For Trailer Valet
Updated 08/01/2026 | Published 11/25/2014
Products Featured in This Question
Question:
Do you have a drawing showing dimensions for this bracket? Is the pipe a standard size that a typical 3000LB capacity trailer jack would fit on? What is the weight rating for this bracket? Thanks
asked by: Russ
Helpful Expert Reply:
There is no weight rating for the Mounting Bracket, part # TV-0002. It is designed to replace the bracket for the Trailer Valet Trailer Jack, part # STC-V211. The Trailer valet has a weight capacity of 500 lbs.
You may be able to install a different trailer jack in the bracket but since they do not test the bracket with any other manufacturer items, I cannot give you a weight capacity for the bracket or a guarantee it will work.
I pulled one of the # TV-0002 from our warehouse and took some measurements for you. The bolt holes on the mounting pipe are 5/8 inch diameter. The inside diameter of the pipe mount is 2-3/8 inches and the outside diameter of the pipe is 2-3/4 inches, and the pipe mount is 2-3/8 inches deep. The overall height of the bracket is 8 inches, and the width of the bracket overall is 7-1/2 inches. The mounting bracket is 2-5/8 inches deep. I have attached a photo of the bracket with the dimensions you asked about noted.
This bracket can be mounted on trailer frames up to 2-3/4 inches wide x 6 inches tall.
Product Page this Question was Asked From
Replacement Mounting Bracket for Trailer Valet Swivel Jack and Trailer Mover
- Accessories and Parts
- Trailer Dolly
- Trailer Jack
- Trailer Dolly Parts
- Mounting Brackets
- Trailer Valet
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: trailer dolly
- Video: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers Review - 2025 Mazda CX-5 - e38FV
- Shop: BTBRV Magnetic Hitch Receiver Reducer Set - 3" to 2-1/2" & 2-1/2" to 2"
- Shop: Replacement Mounting Bracket for Trailer Valet Swivel Jack and Trailer Mover
- Video: Swagman Stratus RV Frame Mount 2 Bike Rack Feature Review
- Search Results: wheel chocks
- Search Results: trailer valet parts
- Search Results: trailer jack mount
- Search Results: locks
- Shop: etrailer Bolt-On Swivel Mounting Plate for 3,500-lb Trailer Jacks with a 5/8" Swivel Pin
- Search Results: pipe mount
- Shop: Trailer Valet JX Drill Powered Jack - Pipe Mount - 14-1/2" Lift - 1,800 lbs
- Search Results: 2 x 2 trailer tongue
- Shop: Weld-On 2" Diameter Pipe Mount Tube for Pipe Mounted Trailer Jacks
- Shop: Replacement Male Pipe for etrailer and Ram Pipe Mount Swivel Jacks - 2" - 5/8" Pin Hole
- Video: Trailer Valet Trailer Jack TV-0002 Review
- Video: Brand Motion Camera Systems Spotlight
- Video: Review of Trailer Valet Trailer Jack - Trailer Jack Welded Pipe Mount Sidewind - TV35FR
- Video: Review of etrailer Bolt on Swivel Jack Mounting Plate - e52JR
- Shop: Suspension Enhancement
- Video: Review of Parkit360 Trailer Dolly Hitch Adapter - PA78VR
- Shop: Replacement Male Pipe for Curt Pipe Mount Swivel Jacks - 2"
- Q&A: Outer Diameter of Weld-On Pipe Coupling on Trailer Valet JX Trailer Jack
- Shop: Trailer Wiring
- Q&A: What Are The Lengths Of The Extreme Off-Road Ratcheting Trailer Jack w/ Wheel # ORJW1SU?
- Q&A: Recommended Best Trailer Tongue Jack for Maneuvering in Tight Areas and on Gravel or Soft Terrain
- Q&A: Will Air Lift 1000 for 2025 GMC Acadia Fit 2025 Chevy Traverse
- Shop: Vehicle Tow Bar Brake System
- Q&A: Mounting Plate Dimensions For ARK Xtreme Off-Road Ratcheting Trailer Jack # ARK54FR
- Q&A: Extended and Retracted Height of ARK ORJW1SU Extreme Off-Road Ratcheting Trailer Jack
Laurie
8/1/2026
Does anyone make a bolt on version of this mount for the trailer valet? I have a small utility trailer and this mount is just too large to fit well on it. Thanks.