Best Place on a Boat Trailer Frame to Install the Trailer Valet Swivel Jack and Trailer Mover
Published 06/10/2014
Question:
I have a 2013 Mastercraft X 30 with the tandem trailer that came with the boat. The boat and trailer combined way 5300 pounds. I am needing to maneuver the boat on the trailer into and out of my garage and it is very tight corners to turn around. I am only needing to move it about 10 feet into the garage and then about 10 feet out of the garage. I am have purchased a Trailer Valet jack wheel to help maneuver it into and out of my garage. I am not going to remove the swivel wheel Jack that came with the trailer. Because I am at the upper limit weight wise of what the Trailer Valet supports, where is the optimal spot to place the Trailer Valet? Is it on the opposite side of the trailer from where the factory swivel jack wheel is? Or would it be better to place it closer to the tongue so the weight is more evenly distributed on the Trailer Valet? I am not sure where most of the weight is distributed on the trailer, at the front of the tongue or closer to the A-frame section of the trailer.
asked by: Brent B
Expert Reply:
The further forward on a trailer the less weight there is. If at all possible, move the Trailer Valet, # STC-V211, as far forward as you can on either side. The OCD in me wants to say put it on the opposite side as the regular jack.
A boat trailer usually has lower tongue weight than a regular trailer because the motor on the back of the boat is weighing it down on that end. That should keep you within the tongue weight capacity of the Trailer Valet, which is 500 pounds.
You could also use both jacks at the same time if you are concerned about the weight and capacity.
Product Page this Question was Asked From
Trailer Valet 5X Swivel Jack and Trailer Mover - Topwind - 15" Lift - 5,000 lbs
- Trailer Dolly
- Manual Dolly
- 5000 lbs
- 15 Inch Tall
- Trailer Valet
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Valet 5X Swivel Jack and Trailer Mover - Topwind - 15" Lift - 5,000 lbs
- Search Results: trailer valet
- Shop: Replacement Drill Attachment for Trailer Valet XL, V2, or MV PRO Trailer Dolly
- Shop: Rack'Em Trailer Dolly
- Q&A: What Is the Minimum Height of the Trailer Valet 5X Swivel Jack and Trailer Mover
- Q&A: Can Trailer Valet Swivel Jack # STC-V211 be Used on Trailer with Sway Control
- Q&A: Trailer Valet STC-V211 Mounting Bracket Dimensions
- Q&A: Trailer Valet 5X on Trailer With Propane Tanks on the Tongue
- Q&A: Drill Attachment to Use with Trailer Valet Trailer Dolly STC-V211
- Q&A: Can Trailer Valet 5X Swivel Jack and Trailer Mover Fit 2016 Little Guy Silver Shadow
- Q&A: Recommended Trailer Dolly For A Teardrop Camper With A Max Coupler
- Shop: Elbow Joint for Trailer Valet Side Mount Dolly Brackets
- Shop: Trailer Valet XL Mounting Bracket
- Article: Trailer Wiring Diagrams
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Trailer Hitch
- Search Results: trailer hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Feature Breakdown: Universal Installation Kit for Trailer Brake Controller
- Shop: Trailer Wiring
- Search Results: trailer tires and wheels
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: trailer jack
- Article: How to Measure for Trailer Hitch Drop
- Shop: Suspension Enhancement
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: trailer wiring
- Video: Installation: Curt Trailer Hitch Receiver on a 2017 Subaru Outback Wagon
- Shop: Brake Controller
on Trailer Dolly
