Could the Trailer Valet Be Used with a Weight Distribution System

Question

Question:

I would like to order the Trailer Valet but am concerned that it will not rotate up with my current stabilizer system 14-5605 6K E2 Round Bar Hitch. I prefer to not to disconnect it while on the road with my trailer R-pod 179 but just rotate it up. Will it rotate 90 degrees in either direction?

asked by: Bill M

1

Helpful Expert Reply:

The swivel assembly of the Trailer Valet part # STC-V211 would allow it to swivel either forward or back if needed. If you have a weight distribution system most likely you would have to install this jack behind the system or you would have to only use one system or the other as they would most likely interfere.

expert reply by: Jameson C

1

Answer 1

There is no weight rating for the Mounting Bracket, part #TV-0002. It is designed to replace the bracket for the Trailer Valet Trailer Jack, part #STC-V211. The Trailer valet has a weight capacity of 500 lbs. You may be able to install a different…

view full answer...

Answer 2

In order to mount the Trailer Valet Swivel Jack and Trailer Mover, #STC-V211, on your trailer you will need at least 8 inches of free space on the tongue. I have included a picture with some measures listed. As long as you have sufficient clearance…

view full answer...

Answer 3

The Trailer Valet 5X Swivel Jack and Trailer Mover #STC-V211 can work in terms of jacking your trailer up and moving it; however, it is highly unlikely it will be able to be mounted in the horizontal position as there probably won't be enough…

view full answer...

Answer 4

We offer several types of trailer dollies in addition to the Rack-Em unit you referenced, part #RA20. This Rack-Em dolly has a 1-7/8-inch hitch ball, 13-inch tires and a tongue weight capacity of 500-lbs. For the greatest ease and safety when moving…

view full answer...

Answer 5

The only solution we currently offer to manually move your trailer with a Max Coupler would be to use the Trailer Valet 5X Swivel Jack and Trailer Mover #STC-V211 that you were already looking at. This would clamp to the tongue of the trailer and…

view full answer...

Answer 6

Yes the Trailer Valet 5X Swivel Jack and Trailer Mover #STC-V211 that you mentioned would work great on your 2016 Little Guy Silver Shadow 5x10 as it would fit to it easily and also has enough weight capacity. This also would handle the slight…

view full answer...

Answer 7

In regards to the Trailer Valet 5X Swivel Jack and Trailer Mover part #STC-V211, the distance from the bottom of the wheel or ground to the center of the mounting point is 11" while fully retracted.

view full answer...

Answer 8

The Trailer Valet Trailer Dolly part #STC-V211 is included with the drill attachment.

view full answer...

Answer 9

I wasn't sure exactly what dimension you were looking for on the mounting bracket of the Trailer Valet part #STC-V211 so I attached a picture that has nearly every dimension for you to check out.

view full answer...

Answer 10

The further forward on a trailer the less weight there is. If at all possible, move the Trailer Valet, #STC-V211, as far forward as you can on either side. The OCD in me wants to say put it on the opposite side as the regular jack. A boat trailer…

view full answer...

Answer 11

If you only have 1/8 to 1/4 inch of space to close your garage the Trailer Valet you'd need is the part #STC-V211 which attaches to the frame of the trailer because of that would not add additional length to your trailer which would reduce your…

view full answer...

Answer 12

Hey Vincent, the Trailer Valet 5X Swivel Jack and Trailer Mover #STC-V211 has a 5,000 lb total trailer weight capacity so as long as when your trailer is loaded and you need to move it doesn't weigh more than that you'd be fine. Do you know…

view full answer...

Could the Trailer Valet Be Used with a Weight Distribution System

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching