What Size Hole is On the Roadmaster Direct-Connect Base Plate Kit for Connecting the Tow Bar

Question

Question:

Are these 1/2inch or 3/4inch holes for the tow bar clevis attachment?

asked by: Jorge

0

Expert Reply:

The Roadmaster Direct-Connect Base Plate Kit # RM24VR has a 5/8" hole on the tow bar clevis.

If you are needing a pin(s) we have the Roadmaster Hitch Pin and Clip # RM-910034 available that would fit your needs.

expert reply by: Scott S

0

Answer 1

The Roadmaster Direct-Connect Base Plate Kit #RM24VR for your 2020 Jeep Wrangler Unlimited with a factory steel bumper is confirmed to work with the Roadmaster Nighthawk All Terrain, Non-Binding Tow Bar w/ LED Lights - RV Mount - 8K #RM-676 you were…

view full answer...

Answer 2

Roadmaster hitch pins like #RM-316 and #RM-910034 are both rated for 10,000lbs. The GenY hitch pins like the #325-GH-099 are rated for 32,000lbs. If you were using the #RM-316 the only way the lock would fall off is if it wasn't properly seated…

view full answer...

Answer 3

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Tim welcome back! Your ARH15AACBL2 GE AC unit has the old 410a refrigerant in it so the GE Appliances item #GE64FR you were looking at isn't going to work as a replacement. The EPA mandated R32 refrigerant has been used in all new AC's…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

Hey Robert, the only frame mounted base plate kits we have for your 2021 Jeep Wrangler Unlimited like the Roadmaster part #RM-521453-5 require either the factory steel or plastic bumper to verify for sure they will work. For aftermarket bumpers you…

view full answer...

Answer 9

Hey Kirt, Congrats on the new car! To get your car safe to flat tow you'll need the following parts: Base-Plate #RM39FR Tow-Bar Adapter #RO64FR Lighting #RM-15267 Chargeline #RM-156-25 Air-Force One Vehicle Side #SM99209 and Hose #SM99666 (if you…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

Hey Steve, thanks for reaching out! The Roadmaster Direct-Connect Base Plate Kit #RM87NQ fits your 2025 Ford Maverick as long as it's the Hybrid model that doesn't have the engine block heater. It doesn't come with the 6-Pin connector,…

view full answer...

Answer 12

Hey Lucian! There are definitely a lot of options out there, and the best is usually a mix of parts from different manufacturers. We don't have a package under a single part number but I can give you a list of parts for a complete setup. I…

view full answer...

What Size Hole is On the Roadmaster Direct-Connect Base Plate Kit for Connecting the Tow Bar

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching