Recommended Electric Truck Camper Jacks for a 2007 Lance 815

Question

Question:

Could anyone recommend a good conversion kit manual to electrical for an 815?

asked by: Simon P

0

Expert Reply:

We do have an electric option available that may work for you. The HappiJac Electric Truck Camper Jack System # LC736514-ELKIT will have a higher capacity of 8,800 pounds, but does only have 34-1/2 inches of lift. This will also include the mounting brackets which are designed to fit most campers on the market, but will also be a permanent installation.

If this amount of lift and style of install will work for your needs, I will say this is a very good upgrade.

expert reply by: Lazer S

0

Answer 1

Tom, the HappiJac Camper Tie-Downs #LC182904-182971 does not come with a stabilizer bar like #LC205221.

view full answer...

Answer 2

A junction box/7-way plug kit like Epicord #277-000141 or #HS381-9000 lets you convert the camper to match the 7-way RV blade type connector format. This avoids the extra connection points and potential trouble spots from using separate adapters.…

view full answer...

Answer 3

We don't currently have any customer submitted photos for the Brophy Heavy Duty Cable Camper Jacks #CX74, but we do for the lower capacity #CJ74, which uses the same lift brackets. From the edge of the tube to the lift bracket is approximately…

view full answer...

Answer 4

Yes, technically the camper needs to hang over truck bed rails for the Brophy Heavy Duty Cable Camper Jacks - 67" Max Lift Height - 4,000 lbs #CX74 to get under the camper and lift it up properly. This should be self-explanatory, but if the…

view full answer...

Answer 5

In order to choose the correct high-low adapter to flat tow your Fiat, you will need to take some measurements. With your RV and Fiat on level ground, measure from the ground to the center of your hitch receiver. Then measure from the ground to the…

view full answer...

Answer 6

Hey Doug, I checked with Brophy and the Brophy Camper Jacks #CX74 have a distance of 3 inches from the upright mast to backside of the bracket that would hold your camper shell. We do not have a version of this without the feet.

view full answer...

Answer 7

Hello Roger, great question. The Draw-Tite Max-Frame Trailer Hitch Receiver #76227 can indeed be used as a jack point for lifting the vehicle. What I recommend doing is using the receiver or crosstube of the hitch to raise the vehicle off the ground,…

view full answer...

Answer 8

For your horizontal clearance this will really come down to your specific truck as well. The Brophy Cable Camper Jacks have an offset lifting point that is designed to even with the legs of the jacks themselves. So if your truck has fenders that may…

view full answer...

Answer 9

You should not have a problem with the camper sliding out when you are using any of the Brophy Cable Camper Jacks. The jack is very stable because of the tripod base. That stability will make the jack very difficult to tip to the front or the back.…

view full answer...

Answer 10

Hey Keith, it sounds like you're looking for the TorkLift StableLoad Suspension Upgrade for Upper Overload Springs #TLA7200. These will bolt to your frame mounted overload bump stop bracket, has a simple no drill install, and is a universal fit…

view full answer...

Answer 11

Hello Jeff, Sounds like you’ve got a big camper (about 4,000 lbs) on your 2024 F-350 dually, and when it’s loaded, the truck feels bouncy and sways a bit. That’s pretty common with heavy campers, especially if the suspension is still stock.…

view full answer...

Answer 12

The Timbren TFRTT350J will measure 7" from the top of the bracket to the bottom of the rubber spring/jounce. With you having 8-1/2" of space on your 2022 Ford F-250 Super Duty, you will have a 1-1/2" gap between the bottom of the…

view full answer...

Recommended Electric Truck Camper Jacks for a 2007 Lance 815

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching