Parts Needed To Install Redarc Tow-Pro Liberty RED24FR In 2007 Toyota 4Runner

Question

Question:

Hi, I want to install The Redarc Tow Pro Liberty # RED24FR to my 2007 Toyota 4runner? 1 is this a good choice? 2 what type of Mounting Panel and Harness do I need? thanks...

asked by: Agah

0

Expert Reply:

The Redarc Tow-Pro Liberty # RED24FR you were looking at is a great option for your 2007 Toyota 4Runner as long as the trailer you plan on towing does not have more than 2 braking axles. If your trailer has more than 2 braking axles you will need the # RED44FR instead as it is compatible with up to 3 braking axles.

This controller is nice due to it having only a knob visible, instead of an entire controller that you hit your knees on when getting in and moving around.

To mount the # RED24FR you will want to mounting panel # 331-TPSI-007 which will replace one of the blank switch panels in your 4Runner.

If your 4Runner has the factory 7-way trailer connector you will need the # 3040-P and # 331-TPH-017 which will plug into the factory trailer brake controller port underneath the dash of your vehicle, and will get connect directly into the # RED24FR.

If your 4Runner does not have the factory 7-way connector you will need to add one starting with the # 119178KIT, and then installing the # ETBC7.

Once those are installed you will need the # RED69FR and make the following connections:

Black wire to battery with 30 amp circuit breaker included with # ETBC7
White wire to ground
Blue wire to blue wire of # ETBC7
Red wire to cold side of stop light switch that only has power when brake pedal is pressed. Using a circuit tester like # PTW2993 will allow you to find the correct wire to connect to.

I included videos of the products mentioned for you to take a look at.

expert reply by: Samuel C

0

Answer 1

The double bonded wire of the Wiring Kit for 2, 4, 6, and 8 Brake Electric Trailer Brake Controllers #5506 that you referenced carries two circuits to the battery of the vehicle for installing the brake controller. The black wire is the power wire…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Parts Needed To Install Redarc Tow-Pro Liberty RED24FR In 2007 Toyota 4Runner

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching