Dimensions Of Stromberg Carlson Electric Trailer Jack SC63VR

Question

Question:

can you give me dimensions from picture below thanks

asked by: John A

0

Expert Reply:

Absolutely!

From the top of the Stromberg Carlson Electric Trailer Jack # SC63VR to the mounting flange is 21-1/4" and from the front of the jack to the tube is 5-5/8" as shown in the included diagram.

I included a video of the # SC63VR for you to take a look at.

expert reply by: Samuel C

0

Dimensions Of Stromberg Carlson # S63VR
(click to enlarge)

Customer Picture
(click to enlarge)

Answer 1

Hey Carl, I think I have a better solution but I would need more info from you to give you the exact part number you need. So your best solution will be a ball mount that has a longer distance between the hitch ball hole and the hitch pin hole. So to…

view full answer...

Answer 2

Yes the 18 inch Equal-i-zer shank part #EQ90-02-4500 will work great in your truck hitch and with your Equal-i-zer weight distribution system. The longer length will give you the clearance you are wanting.

view full answer...

Answer 3

Sounds like a damaged screw/gear inside your trailer jack. That specific model is no longer made so for a replacement the upgraded version part #JET-5000 would be your best option. This has a higher capacity so it would work a little quicker too.

view full answer...

Answer 4

I would be happy to help you. Based on the information you have given me I am going to give you the height of the Stromberg Carlson Electric Trailer Jack Item #SC63VR you referenced. This jack sits 21 1/4" above your trailer's frame. You…

view full answer...

Answer 5

The Stromberg Carlson Electric Trailer Jack #SC63VR will require a 12V battery that can handle a 30 amp draw. You will want to choose a battery based on the amp hours. A smaller battery like a lawn mower or motorcycle battery could potentially work,…

view full answer...

Answer 6

The Stromberg Carlson Electric Trailer Jack #SC63VR you were looking at has mounting holes that are 3" apart on center. This is the standard mounting hole pattern used by virtually all a-frame trailer jacks, so it will be an exact replacement…

view full answer...

Answer 7

Hey Mike! The etrailer Electric Trailer Jack #e55ZV would be a great replacement for the jack on your 2021 Jayco Jay Flight 242BHS. This has the same lift as your existing jack but with a higher 5,000 lb capacity making it a nice upgrade. It also…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Dimensions Of Stromberg Carlson Electric Trailer Jack SC63VR

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching