etrailer Trailer Hitch Receiver # e98846 Driver's Side Mounting Bracket Clearance of Exhaust Hanger

Question

Question:

I have a 2011 Rogue SV AWD and the Draw-Tite 75902 driver side cant mount because the vertical part the frame mount is too tall and the driver side frame mount extends under a welded-on mount for the exhaust dampener. Will e98846 bolt on?

asked by: Bryce

0

Expert Reply:

The etrailer Trailer Hitch Receiver # e98846 will have a larger notch for the exhaust hanger on your 2011 Nissan Rogue that is coming into contact on your Draw-Tite Hitch # 75902.

I felt that the best way to show you is with a picture that I have included of the etrailer hitch installed on the Nissan Rogue. You can see where the bolt hole is in relationship to the notch in the receiver for the exhaust mount. This will help you to see if the exhaust hanger on your Rogue will interfere with the hitch, as the angle of your picture will not give me a clear enough representation on your specific Rogue.

expert reply by: Bud M

0

etrailer # e98846 Drivers Side Mount
(click to enlarge)

Customer Image
(click to enlarge)

Answer 1

What you can do is use a bolt leader like #80101-1 with a carriage bolt block through an open portion of your frame to basically act as a weld nut so you can install the hitch. This normally is a solution we use when a vehicle has a broken weld nut…

view full answer...

Answer 2

While there are options for your 2018 Nissan Rogue, the Hollywood Racks Over-the-Top 2 Bike Carrier for Vehicles w/ Spoilers #HRF2 is not a confirmed fit. The Nissan Rogue got a facelift in 2017 that made it hard to put trunk mounted bike racks on…

view full answer...

Answer 3

Yes, the etrailer Trailer Hitch Receiver item #e98846 fits all models of the 2019 Nissan Rogue including the special edition. This hitch is custom fit and bolts directly to your frame with included hardware. It installs in preexisting holes and does…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

etrailer Trailer Hitch Receiver # e98846 Driver's Side Mounting Bracket Clearance of Exhaust Hanger

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching