Replacement Wheel Stud with 1/2 x 20 and .62 Spline Diameter

Question

Question:

I need 8 studs 1/2 X 20 2 inch thread length with a .62 spline diameter. Do you have such a stud.

asked by: Paul

1

Helpful Expert Reply:

It sounds like the Trailer Hub Wheel Stud - Drive In - 1/2" Diameter x 2" Long - Qty 1 # 7-122 is what you're looking for. This is a 1/2" x 20, 2" long stud with a .61 spline diameter-which is the closest we've got to your .62; this could just be down to a slight difference in the measurements taken and I believe this should work for you.

expert reply by: Erik B

1

Answer 1

Are the wheels on your TeeNee Trailer hub piloted or lug piloted? If they are lug piloted then you would only need to make sure the size of the pilot hole on the wheel exceeds that of your trailer hub. It does not need to match this or the wheel you…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 5

Hey Adam, we have just what you are looking for with the B and W fifth wheel rail kit part #BWRVK2402 which is a confirmed fit for your 2017 Ford F-250 and is the industry standard rail design which means it will fit the hitch you have. This is a…

view full answer...

Answer 6

Hey Tim, we do have other options as well that fit the 2.5 inch hitch size like with the Weigh Safe True Tow part #WS59MR which your tongue weight would work great with and comes with a shank that can do a drop of up to 6 inches. This also has a…

view full answer...

Answer 7

Hi Seth! The B&W Patriot 5th Wheel Trailer Hitch w/ Slider - Dual Jaw - 18,000 lbs #BWRVK3270 will fit any industry standard rails (also referred to as ISR) perfectly, but there are technically a few rails out there that it will not fit. Those…

view full answer...

Answer 8

Tony, that's a great question, and you're absolutely right to double-check before ordering. Yes, etrailer part #PD69RR is the Progressive Dynamics PD9345V converter charger. The PD69RR number is our internal etrailer part number, while…

view full answer...

Answer 9

Hello Sean, Thanks for writing in. For a replacement hardware kit you will want to order the Replacement Hardware Kit for Trailer Hitches #RHK. Above "ADD TO CART" you will need to put "Curt C15410" so the warehouse knows what…

view full answer...

Answer 10

Hey Aaron, welcome back! Since your 2017 Ford F-250 has 5th wheel rails installed you've got a wide range of options. The Demco Autoslide 5th Wheel Trailer Hitch item #DM8550035 you were looking at would definitely work. This is the Cadillac of…

view full answer...

Answer 11

Hello Danny, I’m really glad you mentioned the Equalizer! When sway is the issue, that one and the Weigh Safe are definitely my go-to options. They both have 4 point sway control, with straight spring bars and frame brackets. They can be a little…

view full answer...

Answer 12

Hey Jon, I have a solution for you but I would not recommend the Andersen Weight Distribution system part #AN33VR for your 2025 Brinkley Z Air 297. What we have found is that the Andersen system does a decent job with lighter weight trailers but for…

view full answer...

Replacement Wheel Stud with 1/2 x 20 and .62 Spline Diameter

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching