What Might Cause Lippert Smart Jack To Work Going Up but Not Down

Question

Question:

I have smart jack and when you push to have it raise up it clicks all most like a dead battery? It will come up fine but not down ,

asked by: Michael H

0

Expert Reply:

Sounds like the screw or the motor of the Lippert Smart Jack # LC643589 is damaged or has an internal issue. The switch is obviously working and the motor works in the harder direction so something funny is wrong with it. If it's within a year old it's covered under warranty but if not it's time to buy a new one.

expert reply by: Jameson C

0

Answer 1

The Handrail for Second Generation 4-Step MORryde Steps #MR73AR is designed to be used with the StepAbove steps. Unfortunately this rail will not work for your MORryde Flip Tread RV Steps #MR42UR. That being said, the best solution is to add a…

view full answer...

Answer 2

If the motor on your Husky Electric Trailer Jack HT87247 works when lowering but cannot raise there are a couple of possibilities. The power supply feeding the jack may not be sufficient for the load; the 12v feed on a vehicle 7-way may not be…

view full answer...

Answer 3

It sounds like you may have an issue with either the wiring or with the internal circuitry inside the Lippert Smart Jack #LC643589 itself. Check your 12v positive connections both on the battery terminal and inside the fuse holder for corrosion or…

view full answer...

Answer 4

The Lippert Smart Jack Electric Trailer Jack w/ Footplate #LC643589 doesn't really give you much of an option when it comes to troubleshooting so I recommend first checking that it's getting 12 volts with a multimeter #PT89ZR. The only other…

view full answer...

Answer 5

Try removing the fuse in the power wire of your Lippert Smart Jack Electric Trailer Jack #LC643589 for about 15 minutes to do a hard reset. I reached out to my contact at Lippert who told me that this should fix it. If it doesn't just let me know…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 10

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

What Might Cause Lippert Smart Jack To Work Going Up but Not Down

Product Page this Question was Asked From

Continue Researching