Replacement Endcap for Thule AeroBlade Crossbars SOA567X020

Question

Question:

I am missing the end cap to my Thule Crossbar Set. Model# SOA567X020 Do you guys carry them?

asked by: Andrew K

0

Expert Reply:

We do have exactly what you need, as the SOA567X020 are for some Subarus and are the same as the Thule AeroBlade crossbars. So for the replacement endcaps you will need the following (depending on the one you are missing):

- Driver's Side: Replacement Endcap for Thule Aeroblade Load Bars # 752-2867001

- Passenger's Side: Replacement Endcap for Thule Aeroblade Load Bars # 752-2867002

expert reply by: Kyle S

0

Answer 1

Hi George, Yep, you got it right; the correct replacement for the passenger's side of your Thule AeroBlade 60 crossbar is indeed the Replacement Endcap for Thule Aeroblade Load Bars - Passenger Side #752-2867002.

view full answer...

Answer 2

Thanks for the picture of the bars of your Subaru roof rack. What you have are basically the Thule Aeroblade bars so for end caps you'd want part #752-2867002 for the passenger side or part #752-2867001 for the driver's side.

view full answer...

Answer 3

Hi Mike; I'm sorry these are giving you so much trouble but I don't have any secret installation method for the #TH1500052333 on your roof rack. The best I can say is to make sure you get it aligned properly as you push them on. Since the…

view full answer...

Answer 4

The part number you mentioned is the Subaru/Thule Aeroblade crossbar so for a replacement rubber strip you would need the part #TH69JH.

view full answer...

Answer 5

The photo is of a Thule AeroBlade crossbar, and we do indeed have the end caps for that bar, though the rubber strips have been discontinued; the correct caps are the following: - Replacement Endcap for Thule Aeroblade Load Bars - Driver Side…

view full answer...

Answer 6

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Endcap for Thule AeroBlade Crossbars SOA567X020

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching