How Tall is the Backing Plate of the Single Axle Trailer Fender HP36VR

Question

Question:

What is the dimension from the top of the fender to the bottom of the back plate? Looks like it might be about 13 inches, but really need to be sure since this will be exposed on the interior of the camper and I need it to be low enough to seal against moisture intrusion.

asked by: Howard A

0

Expert Reply:

The backing plate of the # HP36VR measures 12". I was able to pull this part from our warehouse and measure it to confirm.

expert reply by: Erik B

0

click to enlarge

Answer 1

Yes, you can drill into the Backing Plate #HP42FR. The backing plate itself is not strong enough to support the weight of the Fender #HP48VR so you must make sure you attach the fender itself to your trailer or have Mounting Brackets #CE26098G-2 to…

view full answer...

Answer 2

Your trailer appears to have steel fenders and we do offer these as well as tough ABS plastic types and aluminum fenders too. You can see all replacement trailer fenders on the linked page. Just click on your trailer's wheel diameter and your…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

How Tall is the Backing Plate of the Single Axle Trailer Fender HP36VR

Product Page this Question was Asked From

Continue Researching