Front Tie Down that Fits 2003 Ford Super Duty Truck

Question

Question:

Hi is this all I need other than turnbuckles for front camper tie down? Where do I mount them on truck?. I have the rear tiedowns already on truck bumper Thanks!

asked by: Michael W

0

Expert Reply:

Since you only need a front tie down setup for your 2003 Ford Super Duty all you need is the part # LC182910-182971 and you'd be set.

Then for a set of turnbuckles you'd only need the part # LC182895 and have that covered as well.

expert reply by: Jameson C

0

Answer 1

The Happijac tie down kits for both of the vehicles you mentioned are totally different so you'd need to go with the #LC182910-182971 for the 2003 Ford F-250. There isn't anything that would carry over between the two trucks unfortunately.

view full answer...

Answer 2

That's a great question Mike and I have an interesting answer. There actually isn't any specific weight capacity for the HappiJac Truck-Mounted Camper Tie-Downs item #LC182910-182971. These are designed to handle the weight of any truck bed…

view full answer...

Answer 3

Hey Ryan, thanks for all of the info you listed on your 2007 Ford F-250. Based on all of that you would want the frame mounted Torklift tie downs part numbers #TLF2011 and #TLF3004 which do not require any welding or drilling to install.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Front Tie Down that Fits 2003 Ford Super Duty Truck

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching