USA Made Trailer Wheel that is 14 inch with 5 Lug Bolt Pattern

Question

Question:

Hello, Interested in some wheels, Can you tell me where Part Number 460545MBPVD is made? Than you.

asked by: Tim H

0

Expert Reply:

The wheel part # 460545MBPVD that you referenced is made in China but for a USA made wheel that's similar the part # AM20353 is same size.

expert reply by: Jameson C

0

Answer 1

The Taskmaster Steel Modular Trailer Wheels with Black PVD Finish #460545MBPVD are definitely not a flat black paint and I suppose that you could compare them to a black chrome color since they do reflect light very well. I would definitely say…

view full answer...

Answer 2

The pilot diameter of the Taskmaster Wheel #TTW460545WS1 that you referenced is 3.27 inches. The center cap part #AM90175 is designed for 3.19 inch pilot diameters. I might be a tiny bit small but it should work just fine. We don't have caps that…

view full answer...

Answer 3

I have another option for you, but at this time we do not offer any wheel and tire combinations with a 215/75R14 tire mounted and do not have the equipment in-house to mount them ourselves. To get the Dexstar Steel Spoke Trailer Wheel - 14" x…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

USA Made Trailer Wheel that is 14 inch with 5 Lug Bolt Pattern

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching