Availability of Peterson LED Trailer License Plate Light

Question

Question:

Currently have the Peterson incandescent . Do they make an LED that fits the same screw holes?

asked by: Brent

1

Helpful Expert Reply:

The LED version of the # PM436 is part # M296XC but the screw holes are spaced a bit differently, at 3-1/2 inches apart rather than the 3-1/4 of your current lamp. However, Optronics offers an LED license plate light, part # LPL41CB that has the same 3-1/4 inch bolt spacing as the lamp you have now, and it looks very similar.

I've linked to an installation video.

expert reply by: Mike L

1

Answer 1

The Peterson Great White LED License Plate Light #M296XC that you referenced was designed for outside applications like your trailer and is waterproof.

view full answer...

Answer 2

For the clearance light #AL91RB and the matching amber light you would install the lights in the appropriate bases like #A91BB and then use 2-wire pigtail #A46PB, plug it into the backs of the lights and attach the wires to the existing trailer…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 11

From what I can find the Norcold N306.3 fridge has a 2.7 cu ft capacity and is 20-1/8" wide and 26" tall. The most similar option we can offer is the 3.2 cu ft Everchill RV Mini Refrigerator #324-000111. The #324-000111 measures…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Availability of Peterson LED Trailer License Plate Light

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching