Distance Between Mounting Holes On the Curt Trailer Hitch Receiver C15445

Question

Question:

What is the approximate distance between the mounting holes on the hitch front to back to bolt to the frame

asked by: Gerald A

0

Expert Reply:

In regards to the Curt Trailer Hitch Receiver part # C15445, the distance between the top two mounting holes front to back is 17.695".

expert reply by: Conner L

0

Answer 1

The distance from the mounting surface of the Curt #C15845 down to the top of the hitch opening is 6 inches.

view full answer...

Answer 2

I spoke with my contact at Curt about trailer hitch #C15445. He said that from the rear most attachment points on the vehicle to the top of the cross tube is 5-1/2 inches. If this is not a great enough distance to accommodate the step bumper and ramp…

view full answer...

Answer 3

I have a couple of options for hitches for your 2001 Ford F-450 cab and chassis depending on whether or not you want a 2" receiver or a 2-1/2" receiver. I have listed both options below: 2" Hitch - Curt Trailer Hitch Receiver item…

view full answer...

Answer 4

The Draw-Tite Trailer Hitch Receiver #DT45516 has a receiver drop of 5-1/2" from the frame. The width of the rear most bolt holes are 30-13/16" from center of hole to center of hole. I have included these measurements on the picture below.

view full answer...

Answer 5

Since a 34 inch wide frame is a standard frame dimension for a cab and chassis truck you could pretty easily make a hitch designed for a cab and chassis truck like the Curt Class V part #C15445 fit. You'd have to drill holes in the frame for the…

view full answer...

Answer 6

The Curt Trailer Hitch Receiver part #C15445 which is a fit for a Ford F-Series Cab and Chassis has a drop of 5-1/2" when measuring from the top of the mounting flange or bottom of the frame to the top cross tube. I have attached a photo of this…

view full answer...

Answer 7

No, Chris, the adjustable #WS97WR and #WS52ER, and all Weigh Safe pintle hitches, are only to be used in the drop position. The sliding ball mount with built-in scale is designed for safe use in the downward position only, no matter which attachment…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Distance Between Mounting Holes On the Curt Trailer Hitch Receiver C15445

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching