Dimensions For The Draw-Tite Receiver # DT45516 on 1999 Ford F-350 Cab and Chassis

Question

Question:

Can I get some dimensions for the width and the distance from the bottom of the frame where the hitch will bolt on to the top of the for the hitch?

asked by: Digger T

0

Expert Reply:

The Draw-Tite Trailer Hitch Receiver # DT45516 has a receiver drop of 5-1/2" from the frame. The width of the rear most bolt holes are 30-13/16" from center of hole to center of hole. I have included these measurements on the picture below.

expert reply by: Bud M

0

DT45516 Hitch Height
(click to enlarge)

Answer 1

In regards to the Curt Trailer Hitch Receiver part #C15445, the distance between the top two mounting holes front to back is 17.695".

view full answer...

Answer 2

I have a couple of options for hitches for your 2001 Ford F-450 cab and chassis depending on whether or not you want a 2" receiver or a 2-1/2" receiver. I have listed both options below: 2" Hitch - Curt Trailer Hitch Receiver item…

view full answer...

Answer 3

The distance from the mounting surface of the Curt #C15845 down to the top of the hitch opening is 6 inches.

view full answer...

Answer 4

I spoke with my contact at Curt about trailer hitch #C15445. He said that from the rear most attachment points on the vehicle to the top of the cross tube is 5-1/2 inches. If this is not a great enough distance to accommodate the step bumper and ramp…

view full answer...

Answer 5

The Curt Trailer Hitch Receiver part #C15445 which is a fit for a Ford F-Series Cab and Chassis has a drop of 5-1/2" when measuring from the top of the mounting flange or bottom of the frame to the top cross tube. I have attached a photo of this…

view full answer...

Answer 6

Since a 34 inch wide frame is a standard frame dimension for a cab and chassis truck you could pretty easily make a hitch designed for a cab and chassis truck like the Curt Class V part #C15445 fit. You'd have to drill holes in the frame for the…

view full answer...

Answer 7

No, Chris, the adjustable #WS97WR and #WS52ER, and all Weigh Safe pintle hitches, are only to be used in the drop position. The sliding ball mount with built-in scale is designed for safe use in the downward position only, no matter which attachment…

view full answer...

Answer 8

Hi Bry, It looks like the issue might not be with the brake controller after all, but possibly with the wiring. If your #10 fuse keeps blowing when you hook up your trailer to the CURT #C56020 T-Connector on your 2006 Ford van, it’s likely due to a…

view full answer...

Answer 9

I definitely have a photo of the dimensions for the Curt Trailer Hitch Receiver #C15845! In the attached photo you'll see the spacing varies between 30" and 31" depending on which set of mounting holes you're looking at.

view full answer...

Answer 10

Hey Derek! That part number isn't available on our site anymore, but it doesn't look like it was a fit for your 2004 E350 van anyways. I verified some bolt hole to bolt hole measurements on a couple hitches that are a fit for your vehicle:…

view full answer...

Answer 11

Hey Jake, thanks for the measurement. The Curt Hitch item #14053 fits the 1995 Ford E-350's that have bolt holes spaced 38-5/8" from the center to center of your frame. I checked with our vendors and there's no custom fit hitches for…

view full answer...

Answer 12

We see this on occasion and while its super frustrating the issue is that the hitch got bent in shipping and that's why the holes don't line up. If you can find like an open stairwell or some other way to use leverage to bend it back that is…

view full answer...

Dimensions For The Draw-Tite Receiver # DT45516 on 1999 Ford F-350 Cab and Chassis

Continue Researching