Drop From Mounting Brackets to Hitch Opening Curt Hitch # C15845

Question

Question:

What is the drop to the top of the receiver?

asked by: Russell

0

Expert Reply:

The distance from the mounting surface of the Curt # C15845 down to the top of the hitch opening is 6 inches.

expert reply by: Jameson C

0

Drop Dimension
(click to enlarge)

Answer 1

I just went out to the warehouse and measured the Curt Trailer Hitch Receiver item #C15845. I have attached a couple of diagrams with the dimensions of this hitch on them. From the center of the back bolt to the front of the receiver is 26" The…

view full answer...

Answer 2

The Curt Trailer Hitch Receiver - Custom Fit - Class V Commercial Duty - 2-1/2" #C15845 will come down about 8 inches from the frame. It does add some support to help with an underrun in a rear end collision so as long as the drop is enough but…

view full answer...

Answer 3

According to my Curt representative, the drop of the #C15845 hitch is right at 6 inches between the top of the receiver tube and the bottom of the truck frame. We do indeed have a reducer sleeve available, part #C45405. For more drop, a weld-on hitch…

view full answer...

Answer 4

I have attached for you below a detailed dimensional drawing of the Curt Trailer Hitch Receiver part #C15800 which is a confirmed fit for the vehicles listed below. The trailer hitch has a class V rating with 2-1/2" opening which is great for…

view full answer...

Answer 5

Curt 2-1/2-inch Class V hitch #C15845 will fit the 1999 Ford F-450 cab and chassis so long as the frame width (measured outside to outside) is 34-inches. Drilling is required for installation. I went to our warehouse and measured the side-to-side…

view full answer...

Answer 6

The distance from the top of the receiver to where it would mount on the bottom of the truck is 6" on the #C15845 Curt Trailer Hitch Receiver. The distances between the mounting bolts vary so I am attaching a picture showing the different…

view full answer...

Answer 7

The Curt Trailer Hitch Receiver part #13028 could potentially fit your 1966 Chevrolet C10 with aftermarket bumper. However, I would not be able to confirm this as the trailer hitch is only tested with the OEM bumper. I have attached a photo for you…

view full answer...

Answer 8

I spoke with my Curt representative, who tells me that the front face of the receiver would sit 10-3/4 inches rearward of the rear-most mounting hole. If you find the rear most mounting hole in the underside of the frame member and measure 10-3/4…

view full answer...

Answer 9

The Curt Trailer Hitch Receiver - Custom Fit - Class V Commercial Duty - 2-1/2" #C15802 has 3 different hole dimensions for mounting. The two holes closest to the receiver are 36.31 inches on center. The widest holes are 37 inches on center and…

view full answer...

Answer 10

34 inch wide frames are pretty common for cab and chassis vehicles. For a hitch that fits that dimension we have the #C15800 which sits down 7 inches from where it attaches to the truck frame. This would be the best option we have.

view full answer...

Answer 11

I went to our warehouse and took a couple of measurements of the part #C15800. I have attached a photo of the trailer hitch and it has the dimensions noted. It measures 7 inches from the mounting lip to the top of the receiver opening and 9-1/2…

view full answer...

Answer 12

There will be a total of 6 fasteners that will be used to install the Curt Hitch part #C15302. Four come with the hitch and the other two are bolts that are in the truck's frame currently. That is why there are only 4 bolts in the product…

view full answer...

Drop From Mounting Brackets to Hitch Opening Curt Hitch # C15845

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching