Can Camco Hitch-Mounted Flagpole Holder be Used for Patio Umbrella

Question

Question:

Could this item be used with a patio umbrella for shade? Would be great to include the great dimensioned picture provided buried in the questions up in the basic totem info with the pictures. Everyone would find this info helpful....without having to dig into questions to find.

asked by: Jim

0

Expert Reply:

Yes, you can hold a patio umbrella in the Camco Hitch-Mounted Flagpole Holder for 2" Hitch Receivers # CAM51611.

You just need to make sure the pole that holes the umbrella is no more than 2 inches in diameter and you'll have a nice shade wherever you go.

expert reply by: Kyle S

0

click to enlarge

Answer 1

Hi Tim; since the #e55ZV works with the battery we can rule out the wiring as the issue. I'm not sure how you have it connected to the 7-way, but it isn't getting enough power off of your 7-way to run the jack. Most electric trailer jacks are…

view full answer...

Answer 2

Hello Le; the wire on the etrailer Electric Trailer Jack #e79GV is 12 gauge.

view full answer...

Answer 3

I reached out to Curt who informed me you will have to get a whole new weight distribution to upgrade to the Curt TruTrack 2P #C69JR. They said the Spring Bar #C86BR will not fit into your Head 17107. So you would only be able to reuse your hitch…

view full answer...

Answer 4

For a generic fitment I recommend checking out the Replacement Head for Curt TruTrack 2P Weight Distribution System w/ Sway Control #C26BR. This meets all of your criteria so all you have to do is get the Replacement Hardware Kit #C17550 or supply…

view full answer...

Answer 5

Hi Richard; the wire on the etrailer Electric Trailer Jack #e55ZV is approximately 6' long. It uses 12 gauge wiring so if you need more wire you can add #12-1-1 along with some butt connectors #DW05745-1. If you have any other questions feel free…

view full answer...

Answer 6

Hello Johnny, thanks for reaching out. The etrailer Electric Trailer Jack #e55ZV runs off 12v power. The jack has 2 wires so red is positive and black is negative. It is intended to be wired directly to a trailer battery. You could attach the wires…

view full answer...

Answer 7

To check the pins on the vehicle side 7-Way, you can use a circuit tester or the volt meter. The circuit tester will show you if a signal is coming through on the pin you are testing while the volt meter will tell you that and how much voltage is…

view full answer...

Answer 8

Yes, the Curt TruTrack 2P Weight Distribution System w/ Sway Control #C69JR will work with your Jayco Eagle travel trailer. From what I saw the GVWR of this rig was a hair above 7,000 lbs, so the 800 lb - 1,000 lb tongue weight range is perfect for…

view full answer...

Answer 9

The inner diameter of the Camco Hitch Mounted Flagpole Holder part #CAM51611 where the flag installs is 2 inches like you mentioned.

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Can Camco Hitch-Mounted Flagpole Holder be Used for Patio Umbrella

Product Page this Question was Asked From

Continue Researching