Filter Questions and Answers:

reset filter

Expert Answers about Novelty


  • Can I Use the Chevrolet Bowtie LED Emblem on a 2015 Chevy Malibu
  • I don't see any reason why you couldn't install the Chevy Bowtie LED Lighted Vehicle Emblem # RP86618 on your 2015 Chevy Malibu, but the logo is designed to replace the rear emblem on Chevy trucks and is likely going to be larger than the rear emblem on your Malibu. This emblem is 10-1/2" long (wide) and 4" tall.
    view full answer...

  • Would Chevrolet Bowtie LED Lighted Vehicle Emblem # RP86618 Fit 2019 Chevy Tahoe RST
  • The Chevy emblem of your 2019 Chevy Tahoe RST is the same size as what the Chevrolet Bowtie LED Lighted Vehicle Emblem # RP86618 is designed to fit so yes this would fit your Tahoe.
    view full answer...

  • How Does Bowtie Lighted Emblem part # RP86618 Install on 2009 Chevy Silverado
  • I attached an install video for the Bowtie Lighted Emblem part # RP86618 that you referenced that will walk you through the entire process. The red wire goes to the running light circuit, the green to the right turn/stop circuit, and the yellow to the left turn/stop circuit.
    view full answer...

  • Will Ram LED Lighted Vehicle Emblem Fit 2020 Ram 1500 Night Edition
  • Yes, the Ram LED Lighted Vehicle Emblem # RP8609344 that you referenced will work well to replace the factory tailgate emblem on your 2020 Ram 1500 Night Edition (and look really great too). The only thing you will want to be aware of is that on newer trucks like yours some customers have had to drill an additional small hole into the tailgate to feed the wiring through, as the existing hole seems to be just a bit lower than it needs to be. I have attached a short video review that...
    view full answer...

  • Recommended Converter for Manufacturer Logo LED Brake Light
  • Absolutely! The Ford LED Lighted Vehicle Emblem - Black # RP86620 connects to your running light circuit without any converter needed. The converter in the kit is not available separately but I do have a converter that will work perfectly for your application. The way to isolate the brake light signal for this unit is to use the Pacer Performance 3rd Brake Light Logic Module # PP20-702. This is my recommendation for your application. On the emblem the white wire is ground, the brown...
    view full answer...

  • Availability of a Red LED Chevrolet Emblem to Mount to a 2002 Chevrolet Silverado
  • I have a solution for you. The Reese Chevrolet Bowtie LED Lighted Emblem, # RP86618, might be the product that you are needing. The light-up emblem uses heavy-duty tape to install on the rear tailgate of a Chevy truck. However, you may be able to modify the light to install on the front grill of your vehicle. You will need an electrical tester like # 40376 to find the correct wiring at the front end of your truck to tap into the wiring to send power to the emblem. As for a light...
    view full answer...

  • Front Mounting an LED Bowtie Light for a 2001 Chevrolet Silverado
  • The Reese Chevrolet LED Bowtie, part # RP86618 is only available in red and is intended as a tail light, but we have had several customers successfully mount it to the front of their vehicle in various configurations. I've included a picture of one installed onto a puddle light circuit so you can see a potential application.
    view full answer...

  • What Does the Black Box Do for the Ford LED Lighted Emblem
  • The little box that you mentioned is a converter box meant to separate out a turn signal function from a brake light function so that the lighted emblem # RP86620 does not blink when a turn signal is activated. The light itself should have 1 ground wire and 1 power wire. If you attach the power wire to a running/head light wire on your 1986 Mustang then it will light up when the vehicle lights are on and turn off when the vehicle head lights are turned off. I also caution you about...
    view full answer...

  • Installation of Ram Tailgate LED Lighted Emblem
  • The Ram LED Lighted Vehicle Emblem - Black # RP86619 hardwires to your vehicle's tail lights. It uses a 3-wire hookup. The three wires are white (Ground), brown (Running Light) and red (Brake Light), and these connect to, respectively, the ground, running light circuit and brake light circuit. If your vehicle has a 2-wire system, in which one wire is used for both the brake light and turn signal functions, install the included converter to ensure correct performance. A circuit tester...
    view full answer...

  • Dimensions of Ram Emblem Light part # RP86619
  • The dimensions of the Ram emblem light part # RP86619 that you referenced is 5-3/4" wide x 6-1/4" tall. We have found that it fits well on nearly all Ram trucks but you might compare that to the dimensions of your current emblem to know for sure.
    view full answer...

  • What Vehicles Will Ford LED Lighted Vehicle Emblem # RP86620 Fit
  • The Ford LED Lighted Vehicle Emblem # RP86620 referenced in your question can technically be installed on any vehicle, which is why there isn't a specific list available of models that it will work on. If you are wanting to see if this will fit in the same space as the existing emblem on your Ford F-150, you can simply take a few measurements on your truck. This lighted emblem measures 9 inches wide and 3-1/2 inches tall. You can compare this to the factory emblem on your F-150 to see if...
    view full answer...

  • How To Wire the Chevy Bowtie LED Lighted Vehicle Emblem Part # RP86618 on a 2012 Chevy Silverado
  • In order to install the Chevrolet Bowtie LED Lighted Vehicle Emblem part # RP86618 on your 2012 Chevy Silverado, our installers recommend using the Hopkins 4-Pole Loop part # HM48145 along with two packs of the 22-18 Gauge Butt Connectors part # 05730-5. Once you have mounted the emblem to the vehicle and the wires are ran down and out of the tailgate, you will want to cut the 4-pole loop in half and strip back about 3/4" off of the white, brown, and yellow wires on the 4-way connector....
    view full answer...

  • Will the Ford Led Lighted Vehicle Emblem 86620 Fit a Ford Ranger
  • Yes, the Ford LED Lighted Vehicle Emblem part # RP86620 will fit a 2016 Ford Ranger T6. It includes everything you will need for installation. Once you remove the backing on the emblem and apply the adhesive to your tailgate you will then need to run the wires to your vehicle's running, turn, and stop light circuits. If your Ranger has combined lighting you will also need to use the included converter box.
    view full answer...

  • Will Chevrolet Bowtie LED Light Work on 2016 Chevy Silverado 1500
  • The Chevrolet Bowtie LED Lighted Vehicle Emblem # RP86618 is technically a universal part so it will definitely work on your 2016 Chevrolet Silverado 1500. It attaches via heavy-duty tape and connects to your tail lights using the included quick-splice connectors.
    view full answer...

  • Would Ford LED Lighted Vehicle Emblem # RP86620 Interfere with Back Up Camera
  • The Light Up Ford Emblem part # RP86620 that you referenced would not interfere at all with the back up camera of your truck.
    view full answer...

  • How Well Will 3d-Cal Butterfly Vehicle Decal # CR83303 Hold Up in Michigan Weather
  • I spoke with the manufacturer about the 3d-Cal Butterfly Vehicle Decal # CR83303 that you referenced and my contact actually said that they have family who lives in Minnesota and has had similar decals on their vehicles for 5 years now so it will hold up really well in your Michigan weather. To help the adhesive stick really well I would try to get the surface you are installing it on really clean prior to the install.
    view full answer...

  • Ford LED Lighted Vehicle Emblem Dims When Running Lights Are Active
  • The Ford LED Lighted Vehicle Emblem part # RP86620 has two levels of illumination, low illumination and high illumination. The red lights remain set at low illumination when your vehicle's tail lights are on. When you activate your brakes or turn on your hazard lights, the LEDs burn brighter to draw attention to your vehicle. Therefore, I believe you have the emblem installed correctly and it is working as designed.
    view full answer...

  • Will the Ford LED Lighted Vehicle Emblem # RP86620 Fit a 2013 Ford F-150 Fx4
  • Since the Ford LED Lighted Vehicle Emblem # RP86620 can be used for a variety of applications we don't really have it in our fit guide, but I do have some dimensions that I can give you so that you can determine a fit on your 2013 Ford F-150 Fx4. The emblem measures 9" wide x 3-1/2" tall as you can see in the attached picture. The wiring for powering the emblem is located directly in the middle of the emblem on the back side.
    view full answer...

  • Dimensions of Ford LED Lighted Vehicle Emblem
  • I'm not sure the size of your Ford emblem on your 2019 Ford Explorer but I can tell you that the Ford LED Lighted Vehicle Emblem # RP86620 you referenced is 9" long by 3-1/2" tall and it gets wired in via splicing. I have attached a dimensional photo of the emblem as well as a photo a customer sent in of this product on their Explorer that you can check out.
    view full answer...

  • Will Chevrolet Bowtie LED Lighted Vehicle Emblem Fit 2005 Chevrolet Colorado
  • The Chevrolet Bowtie LED Lighted Vehicle Emblem, part # 86092 is designed for the very thing you asked about. It does fit the location the OEM emblem is currently at. I have attached a photo of the emblem with the dimensions noted. This emblem is hardwired into the vehicle tail lights with the included fasteners.
    view full answer...

  • Can LED Chevy Bowtie Emblem be Installed on a 2015 Chevy Tahoe
  • Chevrolet Bowtie LED Lighted Vehicle Emblem # RP86618 is not vehicle specific so you could technically install it on any vehicle; even a Ford! So you can install it on your 2015 Chevy Tahoe. I have linked the video showing an example installation that you mentioned.
    view full answer...

  • Wiring Configuration of Reese Ram LED Lighted Vehicle Emblem RP86619
  • The Reese Ram LED Lighted Vehicle Emblem # RP86619 use a 3-wire hookup. The three wires are white, brown and red, and these connect to, respectively, the ground, running light circuit and brake light circuit. If your vehicle has a 2-wire system, in which one wire is used for both the brake light and turn signal functions, install the included converter to ensure correct performance. A circuit tester like # 40376, demonstrated in the linked video, helps identify what function each wire...
    view full answer...

  • Lighted Emblem Compatibility With Grille Installation
  • The Ford LED Lighted Vehicle Emblem - Black # RP86620 will work wherever you desire to install it. It simply sticks onto your vehicle with heavy duty tape so you can mount it almost anywhere. The size of this emblem is 9 inches wide by 3-1/2 inches tall so you can see if it is a direct replacement for your truck grille.
    view full answer...

  • Lighted Vehicle Emblem for a Ford Ranger with Backup Camera
  • We have exactly what you will need in the Ford LED Lighted Vehicle Emblem part # RP86620. The lighted vehicle emblem can be installed anywhere on the vehicle but more often that not is used to replace the factory emblem. This emblem will illuminate when the running lights are activated and when the brake pedal is applied. A low illumination occurs with the running lights and a high illumination occurs with the brake/hazard lights. The 3M adhesive backing on the emblem will allow you...
    view full answer...

  • Can I Use Ford LED Lighted Vehicle Emblem On Ford Fusion
  • The Ford LED Lighted Vehicle Emblem - Black part # RP86620 will fit your 2018 Ford Fusion Hybrid if you have a space for it. The emblem measures 9" wide x 3-1/2" tall and simply sticks to your vehicle with heavy-duty tape so you can mount it almost anywhere. A lot of customers stick it to the grill of their vehicle. It will need to be wired to the fusions tail lights.
    view full answer...

  • Will the Ram LED Lighted Vehicle Emblem Work on the Front of the Truck as Well
  • The Ram LED Lighted Vehicle Emblem could very likely work for you. The emblem have been different sizes year to year so you will want to measure yours to ensure that the height and width match the 5-3/4" wide x 6-1/4" tall this emblem offers. To get power you can use the front running light circuit and ground the emblem to the chassis or run it through a designated switch in the cab. Check your local laws to ensure that it does not violate any of them. Some areas will not allow a...
    view full answer...

  • How Does Reese LED Lighted Vehicle Emblem # RP86619 Normally Install
  • The Reese LED Lighted Vehicle Emblem, # RP86619, will use a 3-wire connection when installing on your 2013 Ram 1500 truck. The three wires are a white that connects to a ground, a brown wire that will connect to the running light circuit and a red wire that connects to the brake light circuit of your truck. Since we don't have a wiring diagram for your vehicle you'll have to use a circuit tester like part # PTW2993 to test the taillight wiring of your truck and wire accordingly.
    view full answer...

  • Can Chevrolet Bowtie LED Lighted Vehicle Emblem # RP86618 Wire to Vehicle Trailer Wiring
  • Yes, the Chevrolet Bowtie LED Lighted Vehicle Emblem # RP86618 that you referenced was actually designed to wire to trailer taillight harnesses so this would work well for you. I attached an install video for this for you to check out as well.
    view full answer...

  • Ford LED Logo in 7 Inch Wide Size for 2018 Ford Explorer
  • I have an option for you but it isn't a direct fit. Although the Ford LED Lighted Vehicle Emblem - Black # RP86620 is only available in the 9 inch by 3-1/2 inch option, we do have a similar hitch cover that is the correct size for you that you could use in that same way. It is the Ford LED Lighted Trailer Hitch Cover - 1-1/4" and 2" Hitches - Chrome # 86065 or the black # RP86532. Either of these options is the 7 inch by 2-3/4 inch logo. The wiring will be identical to the emblem and...
    view full answer...

  • Is there a Ford Lighted Emblem that Lights Up Blue or White
  • The Ford lighted emblems that we have # RP86620 are only available in red. But we do have a hitch cover that lights up blue and red, # CR-017F, that you might be able to adapt as an emblem. I have linked a video review of it for you.
    view full answer...

  • Are Load Resistors Needed to Install Ram LED Vehicle Emblem on 2016 Ram 2500
  • If your 2016 Ram 2500 isn't working correctly with the LED Vehicle Light # RP86619 the solution we use is to add load resistors on the circuits of the light to increase the load and that circuit. The resistors we have is part # P230004C.
    view full answer...

  • Can the LED Light Ford Emblem be Installed on a 2016 Ford Explorer Sport
  • You could technically install the Ford lighted emblem # RP86620 on any vehicle, including your 2016 Ford Explorer Sport. To determine if it fits in the same space as an existing emblem you can go by the measurements. The lighted emblem is 9 inches across and 3-1/2 inches tall. If the light functions do not run through the hatch then you would have to route the wiring up through the interior of the hatch to the roof line and then route the wires left or right and down to either tail light...
    view full answer...

  • Is a Wiring Converted Needed to Install Lighted Emblem on a 2011 Dodge Ram 1500 Laramie
  • You won't need to add a converter should it be needed when installing the Ram lighted emblem # RP86619. The converter is included. So you won't have to purchase anything else! I have linked a video review of the emblem for you.
    view full answer...

  • How to Install Chevrolet Bowtie LED Lighted Vehicle Emblem # RP86618
  • The Chevrolet logo item you referenced, Reese's Chevrolet Bowtie LED Lighted Vehicle Emblem # RP86618, will install using the included heavy-duty tape. This LED logo can be installed in place of your existing bowtie tailgate logo or be used along with it if you prefer. The heavy-duty tape allows for placement in just about any location on the vehicle. This officially-licensed LED-lighted Chevrolet logo features two levels of illumination, low illumination while you're using tail lights...
    view full answer...

  • Will Chevrolet Bowtie LED Lighted Vehicle Emblem Work on 2015 Chevy Colorado
  • The Reese Chevrolet Bowtie LED Lighted Vehicle Emblem # RP86618 referenced in your question is designed for all Chevrolet vehicles and will work great on your 2015 Chevrolet Colorado. This will be used to replace the factory emblem on your Colorado and will be hardwired into the vehicle's tail lights with the included quick-splice connectors. You can use a circuit tester like # PTW2993 to identify the wire functions in your vehicle.
    view full answer...

  • How to Test Vehicle Wiring for Installation of Reese LED Lighted Vehicle Emblem RP86619
  • You will need to use a circuit tester like # 40376, shown in the linked video, to test the wires at the taillight assembly of your 2016 Ram 1500 to find the ones that carry the running light and stop/turn signals. Vehicles do not use any standardized wire colors for these functions so testing is the best way to determine the wires for connecting a light such as the Reese LED Lighted Vehicle Emblem # RP86619. With this light the white wire is ground, the brown wire connects to the truck's...
    view full answer...

  • Could the Ram LED Lighted Vehicle Emblem # RP86619 Be Installed on Front of Vehicle
  • There is potentially a way to install the Ram LED Lighted Vehicle Emblem # RP86619 on the front of your vehicle so that you could wire it up to come on with the running lights. But in most areas it is illegal to have any red or blue lights on the front of the vehicle as that is commonly seen on emergency vehicles so you would need to check with your local DOT to find out for sure.
    view full answer...

  • Will Ford LED Lighted Vehicle Emblem Work on 2019 Ford Fusion
  • Yes, the Ford LED Lighted Vehicle Emblem # RP86620 will work on your 2019 Ford Fusion, and does come with everything needed for installation, including the quick-splice connectors. It is 9 inches wide and 3 inches tall so you can use those measurements to determine if it has the same dimensions as your current emblem or will be a bit larger or smaller. Even if it is not, it will still be a great replacement because it uses pre-applied heavy tape so you can stick it directly where your current...
    view full answer...

  • How to Install Chevrolet Bowtie LED Lighted Vehicle Emblem
  • The Chevrolet logo item you referenced, Reese's Chevrolet Bowtie LED Lighted Vehicle Emblem # RP86618, will install using the included heavy-duty tape. This LED logo can be installed in place of your existing bowtie tailgate logo or be used along with it. The heavy-duty tape allows for placement in just about any location on the vehicle. The LED-lighted Chevrolet logo has two levels of illumination, low illumination, while you're using tail lights, and high illumination when you brake...
    view full answer...

  • Can the Ford LED Lighted Vehicle Emblem # RP86620 be Installed on a Front Grille
  • The Ford LED Lighted Vehicle Emblem # RP86620 is a universal fit and can basically be installed virtually anywhere. It is 9" wide x 3-1/2" tall and installs with pre-applied heavy-duty tape.
    view full answer...

  • What Can I Use to Replace the Converter Included in Ram LED Vehicle Emblem RP86619
  • There is not a direct replacement for the converter included in the Reese Ram LED Lighted Vehicle Emblem # RP86619, but you can use a 2-To-3 Wire Tail Light Converter like the Curt # C56196 to accomplish the same thing. This converter allows you to split the tail light and turn signal functions, which is required since your 2016 Ram 1500 has a 2 wire system and not a 3 wire system.
    view full answer...

  • Availability of LED Truck Tailgate Emblem for Chevy Truck
  • The closest thing we offer is the part # RP86618 which is a red LED tailgate emblem but it measures 10-1/2 inches wide by 4 inches tall.
    view full answer...

  • Will the LED Ram Emblem part # RP86619 fit a 2016 Ram 1500
  • The Ram LED Lighted Vehicle Emblem # RP86619 fits as a replacement for the standard Ram emblem that measures 5-3/4" wide x 6-1/4" tall. You might want to measure your emblem to be totally sure, but it will fit as a replacement.
    view full answer...

  • What are the Wire Functions for the Ford LED Lighted Emblem
  • For lighted Ford emblem # RP86620 the white wire is ground, brown connects to the running light circuit, red is for brake lights. There is a conversion module that the red wire goes to and on the output side there is a green wire (right turn signal and brake light wire) and a yellow wire (left turn signal and brake light wire). The module is used on vehicles that have the brake lights and turn signals on the same circuit. For 2007 Ford F-150 should have combined turn signals and brake...
    view full answer...

  • Could the Chevrolet Bowtie LED Lighted Vehicle Emblem # RP86618 Install on a Chevy Malibu
  • There's no reason you couldn't install the Chevrolet Bowtie LED Lighted Vehicle Emblem # RP86618 on your Chevy Malibu. It is designed to be installed as a replacement emblem for a truck, but it is pretty universal meaning that if you wanted to install it on a vehicle there would be nothing stopping you. You should note that this emblem is the much bigger emblem you see on the truck tailgates. It measures 10-1/2" wide x 4" tall.
    view full answer...

  • Can Ford LED Lighted Vehicle Emblem be Wired to Tow Package Wiring on 2015 Ford F-150
  • The little converter box, also sometimes called a logic box, included with Ford LED Lighted Vehicle Emblem # RP86620, isn't used for all applications so you could wire the emblem to the tow package wiring if you want to. The tow package wiring will have combined turn signals and brake lights though so if you wired it directly to the tow package wiring the emblem would blink with whichever turn signal/brake circuit it is attached to. The converter box would separate out the turn signals...
    view full answer...

  • Will the Ram LED Lighted Vehicle Emblem Work with 2020 Ram 1500 with Split Tailgate
  • Yes. You are able to install the Ram LED Lighted Vehicle Emblem # RP86619 on a 2020 Ram 1500 with the Split Tailgate feature. You will only need to run this LED lamp to the tail lights on one side of the truck, so the split tailgate never really comes into play. If the turn signal and brake lights on your 2020 Ram 1500 are on the same circuit ( 2 wire system as opposed to 3 wires), you will need to add the Pacer Performance 3rd Brake Light Module # PP20-702 to separate out the brake...
    view full answer...

  • Can Ford LED Lighted Vehicle Emblem # RP86620 Replace Emblem on 2003 Ford Ranger XLT
  • Based on my research it looks like the factory Ford emblem on your 2003 Ford Ranger XLT measures around 5-3/4" wide and 2-1/4" tall, although I do recommend verifying this. The Ford LED Lighted Vehicle Emblem # RP86620 that you referenced is going to be a bit larger, but there's no particular reason it couldn't still be used as a replacement. For comparison the LED emblem measures 9" wide and 3-1/2" tall. I have attached a customer-submitted image as well just so you can get a better...
    view full answer...

  • How to Determine Fitment of Ram LED Lighted Vehicle Emblem on a 2007 Dodge Ram 1500
  • I don't think that the dimensions of your tailgate emblem will be listed anywhere but the good news is that if you use a tape measure like part # 8880622 you can confirm as to whether or not the Ram LED Lighted Vehicle Emblem # RP86619 will work as a replacement part. This emblem measures 5-3/4" wide x 6-1/4" tall. I have attached a photo to demonstrate this as well as a review video where these measurements are taken for you to reference.
    view full answer...

  • Taillight Converter Recommendation for Hitch Cover Light so it Won't Blink with Turn Signal
  • The exact module of the Reese Light Up Emblem part # RP86620 isn't available but you could use the part # 118158 to basically get the same thing. You'd wire this to your vehicle wiring that is separate and then only use the red wire for the stoplight circuit and then tape up the extra wires of the converter and then use the running light circuit you already have from the vehicle wiring and you'd be set.
    view full answer...

  • Can the Ford LED Lighted Vehicle Emblem # RP86620 Wire to a Ford Taurus With Trailer Wiring
  • The wiring of the Ford LED Lighted Vehicle Emblem # RP86620 would be compatible with the wiring of your 2003 Ford Taurus. If your vehicle has separate brake lights from turn signals you would need to use the included signal converter as well. Or if you planned on wiring this to your trailer wiring you would definitely need to use the converter. If there isn't a hole behind your emblem (most likely there wouldn't be) you would need to drill.
    view full answer...

  • How Many Amps Does the Ford Lighted LED Emblem Draw
  • The Ford LED emblem is going to pull less than 1 amp. Closer to 0.3 amps. LED lights draw a fraction of the power of the same size incandescent bulb. It will not overdraw a vehicle wiring system.
    view full answer...

  • Will Ford LED Emblem Fit a 1993 Ford Bronco Eddie Bauer Edition
  • The Ford LED emblem, # RP86620, is not vehicle specific. To determine if it will fit in place of an emblem already on your 1993 Ford Bronco Eddie Bauer edition you will need to go by the measurements. The LED emblem is 9 inches across and 3-1/2 inches tall. If the emblem you have is the same size then the LED emblem will fit in its place.
    view full answer...

  • Will an Automatic Car Wash Damage the Finish on Ram Lighted Emblem # RP86619
  • We haven't had anyone complain about the finish coming off on the Ram lighted emblem # RP86619. But what I recommend, if possible, is to use a touchless car wash because the problems would show up, if they show up, with car washes with brushes that make contact with the vehicle. This product has a 90 day warranty so if the finish started to come off in that period it would be covered.
    view full answer...

  • What Are the Dimensions of Bone Collector Logo Flat Decal # SPGADE1204
  • According to my contact at SPG Novelty their Bone Collector Logo Flat Decal # SPGADE1204 measures 5-1/4- x 5-1/4-inches. These come as a single piece. These vinyl decals are removable and weather-resistant.
    view full answer...

  • SPG Bone Collector Logo Flat Decal # SPGADE1204
  • The SPG Bone Collector Logo Flat Decal # SPGADE1204 is 5-1/4 inches by 5-1/4 inches. I have included a picture with the measurements. That is the only size decal we carry for that specific design.
    view full answer...

  • Dimensions of the Harley-Davidson Key Chain HDKD153
  • The number 1 of the part # HDKD153 that you referenced measures 4 inches long and 1-2/5 inches wide.
    view full answer...

  • How Big is the Bone Collector Logo Flat Decal # SPGADE1205
  • The Bone Collector Logo, # SPGADE1205, measures 5-1/4 inches wide by 5-1/4 inches tall. I made a short video showing how the width and height measurements are taken. We also offer the Bone Collector Hitch Cover, # SPGAHC2001, which would be a nice compliment to the logo decal.
    view full answer...

  • How to Wire the Curt 2 Wire to 3 Wire Conver to the Reese Ram LED Lighted Vehicle Emblem
  • The Reese Ram LED Lighted Vehicle Emblem # RP86619 converter box does not have the output wires in the same manner as the Curt # C56196 and instead has a plug in receptacle on the output side, so this is likely where the confusion lies. On the 2016 Ram 1500 the brake light and turn signals are on a combined circuit, so you'll need to find those wires to install the Curt # C56196; you can use a circuit tester like the # PTW2993 in order to determine which wire carries which function...
    view full answer...

  • Is There A Ford LED Lighted Vehicle Emblem For The 2020 Ford Explorer
  • The Ford LED Lighted Vehicle Emblem - Black Item # RP86620 is designed for the rear of the vehicle because it lights up red and is only available in black with red LEDs. We do not offer a specific emblem for the 2020 Ford Explorer. I recommend measuring your current emblem to see if they match in size.
    view full answer...