Picking Out Replacement Landing Gear for 2006 Cruiser Fifth Wheel Trailer
Published 10/21/2019
Products Featured in This Question
Question:
I got your email. Those measurements are incorrect for my model. The ones I’m taking off are as follows. Distance between mounting brackets is 11 inches The tube is 151/2 inches The distances between the lips that support the wet is 15 1/4 inches The distance from the bottom of lower lip to the bottom of the upper lip is 16 3/8 inches. Now can you help me. Thanks.
asked by: Randall A
Expert Reply:
In order to pick out a direct replacement for the landing gear on your trailer we would need to know the distance between the mounting brackets since the jack info on your 2006 Cruiser fifth wheel trailer isn't readily available. Otherwise you could just have the brackets removed from your trailer by a qualified welder and then install the brackets that come with the Bulldog Tandem Landing Gear Set # BD500162. Either way this landing gear set would work well for you, you just might have to have the brackets of your trailer removed and then install the brackets of the # BD500162.
I attached a picture that shows the dimensions that this landing gear set would fit with.
The jacks would be the correct replacement for Lippert, Venture, and Atwood landing gear, as well as those from a few other manufacturers. The sure way to tell is that if the distance between the mounting brackets (underside of top bracket to top of lower bracket as shown in the diagram) is 17-1/2 inches. If this is the case, the landing gear should fit just fine.
If your frame clamps are instead 20-1/4 inches the Ultra Fab part # UF17-943010 would be a direct replacement.
I'd have to see pictures of the fridge vent or get some dimensions to help pick out the replacement cover.
Continue Researching
- Shop: Ultra-Fab Deluxe Electric Landing Gear Set - Weld On - 38" Lift - 12,000 lbs
- Q&A: Recommended Landing Gear For A 2021 Forest River Cherokee Artic Wolf 5th Wheel
- Video: Checking Out the Ultra-Fab Deluxe Electric Landing Gear Set
- Shop: Lippert Electric Landing Gear Set - 37" Lift - 6,000 lbs
- Shop: Landing Gear Set - 36-1/2" Lift - 8,000 lbs
- Search Results: trailer jack
- Video: All You Need to Know About the Landing Gear Set
- Video: In-Depth Review of the Landing Gear Set
- Q&A: Can Motor be Added to 8,000 lb Bulldog Tandem Landing Gear Set 500162
- Q&A: Replacement Landing Gear for 1998 Carriage Carri-Lite RK 732
- Video: Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors Feature Review
- Search Results: auto leveling
- Q&A: Electric Stabilizing Jack for Wildwood Travel Trailer
- Q&A: Will Lippert Stabilizer Jack # LC298707 Replace 113407 Jacks
- Search Results: 5th wheel landing gear
- Shop: Ark Drop Down Corner RV Stabilizer Jacks - 24" Long Corner Steadies - Silver - Qty 2
- Shop: Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors - 30" Lift - 6,000 lbs
- Search Results: lc276602
- Search Results: reese landing gear
- Search Results: 5th wheel landing jack
- Search Results: front jacks for 5th wheel rv
- Q&A: Replacing Ultra-Fab Landing Gear With Lippert Landing Gear With High-Powered Motor
- Q&A: Can the Lippert Motor LC196308 Replace a Worn Out LCI PN 142178?
- Shop: Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear Assemblies
- Shop: Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Shop: Trailer Wiring
- Video: A Look at the Power Mountain Tallboy 6 Ton Off-Road Bottle Jack with a Military Cargo Trailer
on Camper Jacks
Randall A.
10/21/2019
I got your email. Those measurements are incorrect for my model. The ones I’m taking off are as follows. Distance between mounting brackets is 11 inches The tube is 151/2 inches The distances between the lips that support the wet is 15 1/4 inches The distance from the bottom of lower lip to the bottom of the upper lip is 16 3/8 inches. Now can you help me. Thanks.