Fitment of Lippert High-Speed Power Stabilizer Jack to Front and Rear of RV

Question

Question:

Can the rear model also be used in the front of the RV trailer? I bought two of same product.

asked by: Stan M

1

Helpful Expert Reply:

Yes, the 30" lift Lippert High-Speed Power Stabilizer Jack, # LC298707 can be installed on the front and rear of a travel trailer. Please note that this jack is designed to stabilize your trailer an not to support the full GVWR. Do not use these to lift your RV as doing so will exceed the rated capacity.

expert reply by: Michael R

1

Answer 1

The 113407 stabilizer jack you have now is the standard Lippert stabilizer jack. If you wanted to replace it with the part #LC298707 that you referenced you certainly could. Overall width is 70-15/16 inches and the mounting hole centers are…

view full answer...

Answer 2

We do not have any electric jacks that are designed for what you are wanting to do as the jacks you are referencing are not designed to lift a trailer off the ground.

view full answer...

Answer 3

Thank you for providing that information. Based on that, I recommend the Ultra-Fab Deluxe Electric Landing Gear Set #UF17-943010. These dual electric jacks are a universal fit so the mounting brackets will need to be welded to the frame of your 2019…

view full answer...

Answer 4

We do have motors that you can add to your landing gear. For example, the Landing Gear Set #RVLG-8000 can be operated with the manual crank #RVLG-HDL but you can also add the motor #LC142178 and switch #LG-145236 for effortless operation on your end.…

view full answer...

Answer 5

Lippert has had some upgrades recently for the High-Speed power stabilizer jack so if your current one is from Lippert then the #LC298707 that you referenced is the correct replacement and will fit properly. Attached is a sample installation video…

view full answer...

Answer 6

In order to pick out a direct replacement for the landing gear on your trailer we would need to know the distance between the mounting brackets since the jack info on your 2006 Cruiser fifth wheel trailer isn't readily available. Otherwise you…

view full answer...

Answer 7

It depends on what kind of landing gear you have but it could be a gear issue too. If you could comment below or email me directly with a part number off of your landing gear I would be happy to help you troubleshoot. The Replacement Motor for…

view full answer...

Answer 8

Hey Johnny, thanks for reaching out! I highly recommend using the Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor #LC196308 as a replacement for your 8532-07 motor. According to my research your motor is rated for 5,500 lbs so this motor will…

view full answer...

Answer 9

Thanks for all that good info, and what you have is the Ultra-Fab Deluxe Electric Landing Gear Set #UF17-943010, which you can replace with a Lippert set with a high speed motor on you RV, though you will need to have new brackets welded on. The…

view full answer...

Answer 10

For your 2008 Keystone Everest, I recommend the Lippert Components HD 6500-lbTuson 5th Wheel RV Landing Gear Motor #LC196308 or the high speed #LC141893 along with the Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear…

view full answer...

Answer 11

The Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor #LC196308 will indeed fit your landing gear without modification. It will have the same bolt pattern as the #LC142178 you currently have, but will definitely have a higher capacity. If you…

view full answer...

Answer 12

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Fitment of Lippert High-Speed Power Stabilizer Jack to Front and Rear of RV

Continue Researching