Do The Hitch Ball Holes Line Up On a Curt EZr and B&W Turnoverball for a 2005 GMC Sierra

Question

Question:

I have a bed that originally had a BandW goooseneck hitch installed so the holes are in the bed already. Do you know if this hitch will fit the same holes as the BandW?

asked by: George

0

Expert Reply:

The Curt EZr Double Lock Underbed Gooseneck Trailer Hitch with Installation Kit part # C619-648 hitch ball opening will not line up with the B&W Turnoverball Gooseneck Trailer Hitch hitch ball opening on your 2005 GMC Sierra. The hitch ball opening for the Curt EZr will sit further away from the end of the bed when compared to the B&W Turnoverball. Therefore, the best option for you would be to re-install the B&W Turnoverball Underbed Gooseneck Trailer Hitch part # BWGNRK1059 for 1500 models, part # BWGNRK1067 for 2500 models, or part # BWGNRK1062 for 3500 models.

expert reply by: Conner L

0

Answer 1

It is certainly possible for any axle to wear out enough over time to need replacing. Since the suspension is built into a torsion axle if the suspension part was to wear out pretty much the only solution would be to replace the axle. If the…

view full answer...

Answer 2

Between 4 and 6 inches is typically what is recommended as minimum clearance from trailer overhang to bed rails. If you can level your setup by lowering hitch where you'd have 5 inches you should be fine. Especially if you aren't in an area…

view full answer...

Answer 3

The recommended minimum clearance between gooseneck trailer overhang and truck bed rails is 4-6 inches. I'd recommend 6 inches but a lot of people get by with just 4. Ideally you have at least 6 inches of clearance and the trailer is sitting…

view full answer...

Answer 4

From a function point of view there isn't a huge difference between the two Curt gooseneck hitches #C60712 and #C619-648. You might notice that the EZR has a smaller plate that has larger u-bolts for safety chains and the Double Lock has smaller…

view full answer...

Answer 5

For B&W gooseneck Turnover Ball hitch #BWGNRK1067 you can use 4 inch offset ball #BWGNXA4085. I have linked a video to the right for this ball for you to view.

view full answer...

Answer 6

You will need the B&W Turnoverball Underbed Gooseneck Trailer Hitch #BWGNRK1067 to fit your 2007 Chevrolet Silverado 2500HD Classic with a short bed. As you have a short bed you may opt for the 4" Offset Ball #BWGNXA4085. We also have the…

view full answer...

Answer 7

In order to choose the best weight distribution hitch, you will first need to know your total tongue weight (TW), which is the tongue weight of your fully loaded and ready to go trailer plus the weight of any cargo behind the rear axle of your tow…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Do The Hitch Ball Holes Line Up On a Curt EZr and B&W Turnoverball for a 2005 GMC Sierra

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching