Snap Ring Diameter of Pro Series Round, Snap-Ring Swivel Jack # PS1401140303

Question

Question:

What size hole is on the jack my present jack has a 2-1/2” hole so I will only need to replace jack portion

asked by: Dave B

0

Expert Reply:

The snap ring hole of the Pro Series Round, Snap-Ring Swivel Jack # PS1401140303 that you referenced that mounts on the trailer has an outer diameter of 2-1/2 inches.

expert reply by: Jameson C

0

Answer 1

The best solution would be to replace the handle on your existing Bulldog Jack, #BD171401. You will need Replacement Topwind Handle for Bulldog Round Jacks, #BD500180. I did speak with my contact at Reese and Bulldog and he stated that the internal…

view full answer...

Answer 2

For just the replacement mount for the Bulldog Swivel Jack #BD171401 you'd want the #F500242 and you'd be set.

view full answer...

Answer 3

They make snap ring pliers that are used to remove snap rings. It has two pins on the end that stick into the holes of the snap ring and when squeezed it will open up the ring enough to be removed. You might also try to use 2 regular pliers. With one…

view full answer...

Answer 4

The overall retracted height of the Bulldog jack part #BD171401 that you mentioned from bottom of the jack to the top of the handle is 15-1/4 inches.

view full answer...

Answer 5

You are correct, the Fulton Snap Ring, #FP908600, and Bulldog Snap Ring, #BD500241, are very similar. I went out to the warehouse and pulled both parts to measure them using digital calipers. Both had the following measurements: Inner diameter = 2.28…

view full answer...

Answer 6

A snap ring like #FP908600 can be measured using a set of dial calipers or digital calipers to get the most accurate measurement possible. To measure the inside diameter, on the inside of the rind measure across at the widest point (not at the bottom…

view full answer...

Answer 7

We have a number of jacks that fall within the 3,000 lb to 5,000 lb capacities, however, the only jack that we carry that is similar to the Pro Series, Snap-Ring Swivel Jack, #PS1401020303, is the Bulldog Round, Snap-Ring Swivel Jack, #BD171401. This…

view full answer...

Answer 8

The Fulton Round, Snap-Ring Swivel Marine Jack - Bolt On - Sidewind - 10" Lift - 1,200 lbs #FTJ12000101 has a pilot hole diameter of 2.313 inches and utilizes the Replacement Retaining Ring for Bulldog and Fulton Snap-Ring Jacks #FP908600 which…

view full answer...

Answer 9

The snap ring on the Bulldog Round, Snap-Ring Swivel Jack #BD171401 is 2-5/16". We do offer the Replacement Swivel Snap Ring for Bulldog Jacks #BD500241 if you need a replacement.

view full answer...

Answer 10

Unfortunately, the only information I could obtain from NAPA regarding your 8215214 tongue jack is it is rated for a 5,000lb lift capacity, is 14-1/5" tall and has a top wind handle. The Bulldog #BD171401 is going to be the closest option but…

view full answer...

Answer 11

The distance from the mounting surface to the center of the tube of the Bulldog Jack part #BD171401 measures 2-1/4 inches.

view full answer...

Answer 12

To verify fitment of the Bulldog Round, Snap-Ring Swivel Jack #BD151110 on your trailer you will need to measure the diameter of the Bracket #F500242 on your trailer. The diameter of the outer part of the bracket needs to be 2-1/2" for the…

view full answer...

Snap Ring Diameter of Pro Series Round, Snap-Ring Swivel Jack # PS1401140303

Continue Researching