Distance from Mounting Surface to Center of Jack Tube on Bulldog BD171401

Question

Question:

Hello, I am looking for some dimensions on a product: BD171401. I need to know the distance from the weld-on mounting plate to the center of the tubular housing. If you have any diagrams showing this dimension, they would be much appreciated. Thank you for your time,

asked by: Nick R

0

Expert Reply:

The distance from the mounting surface to the center of the tube of the Bulldog Jack part # BD171401 measures 2-1/4 inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Pro Series trailer jack part #PS1401140303 that you referenced is designed to fit on a pipe mount diameter of 2 inches so if that's the size you have now (it looks like you do) then yes, this would easily fit on the same mount for an easy…

view full answer...

Answer 2

Unfortunately, the only information I could obtain from NAPA regarding your 8215214 tongue jack is it is rated for a 5,000lb lift capacity, is 14-1/5" tall and has a top wind handle. The Bulldog #BD171401 is going to be the closest option but…

view full answer...

Answer 3

To verify fitment of the Bulldog Round, Snap-Ring Swivel Jack #BD151110 on your trailer you will need to measure the diameter of the Bracket #F500242 on your trailer. The diameter of the outer part of the bracket needs to be 2-1/2" for the…

view full answer...

Answer 4

The Fulton Round, Snap-Ring Swivel Marine Jack - Bolt On - Sidewind - 10" Lift - 1,200 lbs #FTJ12000101 has a pilot hole diameter of 2.313 inches and utilizes the Replacement Retaining Ring for Bulldog and Fulton Snap-Ring Jacks #FP908600 which…

view full answer...

Answer 5

You are correct, the Fulton Snap Ring, #FP908600, and Bulldog Snap Ring, #BD500241, are very similar. I went out to the warehouse and pulled both parts to measure them using digital calipers. Both had the following measurements: Inner diameter = 2.28…

view full answer...

Answer 6

The snap ring hole of the Pro Series Round, Snap-Ring Swivel Jack #PS1401140303 that you referenced that mounts on the trailer has an outer diameter of 2-1/2 inches.

view full answer...

Answer 7

I spoke with my contact at Dutton-Lainson and he gave me the dimensions of this Replacement Snap Ring #DL22672. Inner Diameter = 2.27 Thickness = .080 Outer Diameter = 2.625

view full answer...

Answer 8

For just the replacement mount for the Bulldog Swivel Jack #BD171401 you'd want the #F500242 and you'd be set.

view full answer...

Answer 9

In order to find which snap ring you need you would have to measure the outer diameter of the snap ring bracket on your trailer frame. A part like the #DL22672 REPL Snap Ring for Swivel Trailer Jacks - 2-5/16" Inner Diameter will fit trailer…

view full answer...

Answer 10

The overall retracted height of the Bulldog jack part #BD171401 that you mentioned from bottom of the jack to the top of the handle is 15-1/4 inches.

view full answer...

Answer 11

Your 4-pin/5-wire wiring harness is what is called a "wishbone" type which simply means that there are two separate running light wires, one brown and one pink. This allows a separate running light wire for each side of the trailer which…

view full answer...

Answer 12

The best solution would be to replace the handle on your existing Bulldog Jack, #BD171401. You will need Replacement Topwind Handle for Bulldog Round Jacks, #BD500180. I did speak with my contact at Reese and Bulldog and he stated that the internal…

view full answer...

Distance from Mounting Surface to Center of Jack Tube on Bulldog BD171401

Continue Researching